Before Putting The Equipment Into Operation - Dexter 200SHS2.5 Manual De Instrucciones

FR
FR
11. 11. 11.

5. BEFORE PUTTING THE EQUIPMENT INTO OPERATION

5. BEFORE PUTTING THE EQUIPMENT INTO OPERATION
ES
ES
PT
Grit
PT
Grit
60 or less
60 or less
IT
IT
80 – 100
80 – 100
EL
EL
120 – 150
120 – 150
180 – 220
PL
180 – 220
PL
240 or more
240 or more
RU
RU
Attaching sanding paper
Attaching sanding paper
KZ
KZ
power point before making any adjustment.
power point before making any adjustment.
UA
UA
1. Select the required grade of sanding paper.
1.
Select the required grade of sanding paper.
RO
2. Remove any dust or debris from the hook and loop of the base.
RO
2. Remove any dust or debris from the hook and loop of the base.
3. To attach hook & loop type sanding paper simply align the holes in the sanding paper
3.
To attach hook & loop type sanding paper simply align the holes in the sanding paper
EN
EN
4. To remove the sanding paper, peel it away from the base.
4. To remove the sanding paper, peel it away from the base.
5.
Ordinary (non Hook & Loop type) sanding paper can also be used.
5. Ordinary (non Hook & Loop type) sanding paper can also be used.
6. Release the sandpaper clamp from both sides of the sander.
6. Release the sandpaper clamp from both sides of the sander.
7. Insert the end of the sandpaper under one clamp and pull the paper tight over the base
7. Insert the end of the sandpaper under one clamp and pull the paper tight over the base
ensuring the holes align with those in the base and then clamp the other side.
ensuring the holes align with those in the base and then clamp the other side.
8. The sanding paper should be kept tightly clamped over the base, otherwise there could
8. The sanding paper should be kept tightly clamped over the base, otherwise there could
be excessive wear of the base material.
be excessive wear of the base material.
WARNING: Do not continue to use the sander with a sanding paper
WARNING: Do not continue to use the sander with a sanding paper
that is overworn or damaged.
that is overworn or damaged.
WARNING: Do not use the same sanding paper for wood and metal.
WARNING: Do not use the same sanding paper for wood and metal.
Metal particles become embedded in the sanding paper and will
Metal particles become embedded in the sanding paper and will
Eric LEMOINE Eric LEMOINE Eric LEMOINE scour a wooden surface.
scour a wooden surface.
WARNING: Take care to regularly clean out the build up of dust on the
WARNING: Take care to regularly clean out the build up of dust on the
ADEO Services 135 Rue Carnot — CS 00001 59790 RONCHIN — France ( ADEO Services 135 Rue Carnot — CS 00001 59790 RONCHIN — France ( ADEO Services 135 Rue Carnot — CS 00001 59790 RONCHIN — France (
base underneath the sanding paper and not to let the sanding paper
base underneath the sanding paper and not to let the sanding paper
wear completely down before replacing it. Failure to observe these two
wear completely down before replacing it. Failure to observe these two
precautionary measures can lead to damage to the hooks and loops on the
precautionary measures can lead to damage to the hooks and loops on the
base and the sanding paper will not attach properly.
base and the sanding paper will not attach properly.
160
160
GRIT CHART
GRIT CHART
Type Example of use
ADEO Services ADEO Services ADEO Services
Type Example of use
135 rue Sadi Carnot 135 rue Sadi Carnot 135 rue Sadi Carnot Material removal, heavy paint removal,
Material removal, heavy paint removal,
Very Coarse
Very Coarse
shaping wood
shaping wood
CS 00001 CS 00001 CS 00001
Paint removal, rough surface preparation
59790 Ronchin - France ( 59790 Ronchin - France ( 59790 Ronchin - France (
Paint removal, rough surface preparation
Coarse
Coarse (e.g. non-planed wood)
(e.g. non-planed wood)
, , ,
Medium Surface preparation planed wood
Medium Surface preparation planed wood
Sanding between coats
Fine
Sanding between coats
Fine
200SHS2.5
Very Fine
Final finishing
Very Fine
Final finishing
EC EC EC
, , ,
EN 62841-1:2015 EN 62841-1:2015 EN 62841-1:2015
EN 62841-2-4: 2014 EN 62841-2-4: 2014 EN 62841-2-4: 2014
EN 55014-1:2017 EN 55014-1:2017 EN 55014-1:2017
EN 55014-2:2015 EN 55014-2:2015 EN 55014-2:2015
EN 61000-3-2:2014 EN 61000-3-2:2014 EN 61000-3-2:2014
EN 61000-3-3:2013 EN 61000-3-3:2013 EN 61000-3-3:2013
EN 50581 :2012 EN 50581 :2012 EN 50581 :2012
: . : . : .
) ) )
: : :
200 200 200
200SHS2.5 200SHS2.5
, , ,
2006/42/EC 2006/42/EC 2006/42/EC
2014/30/EU 2014/30/EU 2014/30/EU
2011/65/EU 2011/65/EU 2011/65/EU
(EU) 2015/863 (EU) 2015/863 (EU) 2015/863
: : :
. . .
CE: 19 CE: 19 CE: 19
Done in Ronchin : xx/xx/xxxx Done in Ronchin : xx/xx/xxxx Done in Ronchin : xx/xx/xxxx
FR
ES
PT
IT
EL
PL
: : :
RU
KZ
UA
RO
EN
) ) )
117
FR
FR FR
ES ES ES
PT PT PT
IT IT IT
EL EL
EL
PL PL
PL
RU RU
RU
KZ KZ
KZ
UA UA
UA
RO RO RO
EN EN
EN
117 117 127