Hoshizaki DCM-120FE Manual De Instrucciones página 6

9) Select your dispensing choice by pushing
one of the Select Switches - Ice, Ice & Water,
or Water (factory adjusted to the Ice & Water
mode). The lamp of the selected mode lights
up.
0) The ice dispenser stops the ice making process
automatically in  hour or so when the Storage
Bin is filled with ice, and restarts when ice is
used.
) To activate the preset ice portion control, press
the Portion Control Switch (factory adjusted
to the no control mode). To reset the portion
control, press the switch again. See "3.
ADJUSTMENT OF ICE PORTION CONTROL"
for adjustment of the setting.
2) To lock the selected operation modes, keep
pressing the illuminated Select Switch for
5 seconds until it starts flashing. Press the
Portion Control Switch to illuminate the Lock
Lamp. To unlock, press the three Select
Switches together until the Lock Lamp goes
out.
3. ADJUSTMENT OF ICE PORTION
CONTROL
The preset portion control for ice dispensing is
adjustable as follows (factory adjusted to 40 g, or 4.0
on the Display). The actual ice dispensing amount
depends on the water quality and the amount of ice
remaining in the Storage Bin.
) Remove the Apron Panel A by turning the two
screws on both sides counterclockwise with a
coin and pulling the panel toward you.
2) Press the Set Switch. The Display flashes "4.0".
The ice dispensing amount is ten times the
value on the Display and adjustable from 20 g
(2.0) to 990 g (99) while the Display is flashing.
3) To decrease the ice dispensing amount, push
the Ice Switch. To increase, push the Ice &
Water Switch. One push of either switch will
change the amount by 5 g (0.5).
4) With the desired value on the Display, press
the Set Switch. The set value stops flashing
and remains on.
5) Replace the Apron Panel A in its correct
position, and turn the two screws clockwise
with a coin.
All manuals and user guides at all-guides.com
5
4. CLEANUP TIME REMINDER
To prevent stored ice from melting and refreezing,
the Storage Bin must be cleaned up once a day.
The following procedure enables/disables the
Cleanup Lamp to flash every 24 hours after startup
and remind the user of the cleanup time.
 ) R e m o v e t h e A p r o n P a n e l A . S e e " 3 .
ADJUSTMENT OF ICE PORTION CONTROL".
2) Keep pressing the Set Switch and Portion
Control Switch together for 3 seconds until the
Display shows "oF" or "on" (factory adjusted to
"oF").
3) Push the Ice Switch or Ice & Water Switch.
The Display shows "on" or "oF".
4) Press the Set Switch.
5) Replace the Apron Panel A in its correct
position.
6) The cleanup time changes after power failure
or when the Power Switch is turned off during
service hours. To set the cleanup time, turn
off the Power Switch and turn it back on at
the desired time. The Cleanup Lamp starts
flashing every 24 hours at that same time and
goes out after the Push Lever is pressed for
more than 5 seconds.
5. SHUT DOWN
T h i s i c e d i s p e n s e r m u s t b e s h u t d o w n a n d
drained every day at the end of service hours, in
accordance with the following procedure:
) Close the water tap.
2) Move the Ice Making Switch, located on the
bottom left of the Middle Front Panel, to the
"OFF" position.
3) Place a large container right under the Spout,
and keep pressing the Push Lever until no ice
is dispensed.
4 ) R e m o v e t h e A p r o n P a n e l A . S e e " 3 .
ADJUSTMENT OF ICE PORTION CONTROL".
5 ) P r e s s t h e D r a i n S w i t c h . T h e D i s p l a y
illuminates the Drain Cycle sign when a drain
cycle starts, and illuminates the End of Drain
ENGLISH