baltur BT 15 N Manual De Instrucciones página 31

BASIC HYDRAULIC DIAGRAM FOR MULTIPLE TWO-FLAME OR
MODULATING BURNERS USING FUEL OIL (MAX 15 °E AT 50 °C)
1 - MAIN TANK
2 - FILTER
3 - CIRCULATION PUMP
4 - WATER AND SYSTEM DISCHARGE
5 - NORMALLY CLOSED AIR-GAS DISCHARGE
6 - FUEL RECOVERY TANK AND DEGASSING UNIT
7 - NON-RETURN VALVE
BASIC HYDRAULIC DIAGRAM FOR MULTIPLE TWO-FLAME OR
MODULATING BURNERS FUNCTIONING WITH DENSE FUEL OIL
(MAX 50 °E AT 50 °C) AND AUXILIARY HEATER
1 - MAIN TANK
2 - FILTER
3 - CIRCULATION PUMP
4 - WATER AND SYSTEM DISCHARGE
5 - NORMALLY CLOSED AIR-GAS DISCHARGE
6 - FUEL RECOVERY TANK AND DEGASSING UNIT
7 - NON-RETURN VALVE 7 - NON-RETURN VALVE
6 - BY PASS (NORMALLY CLOSED)
9 - ADJUSTABLE PRESSURE REGULATOR, 0.5 - 2 BAR
N.B. The thank for recovery of hot oil (diameter 150 mm, height 400 mm) should be installed as near as possible to The thank for recovery of hot oil (diameter 150 mm, height 400 mm) should be installed as near as possible to
the burner and about 0.5 m, above the pump. the burner and about 0.5 m, above the pump.
6 6 - BY PASS (NORMALLY CLOSED) - BY PASS (NORMALLY CLOSED)
9 9 - ADJUSTABLE PRESSURE REGULATOR, 0.5 - 2 BAR - ADJUSTABLE PRESSURE REGULATOR, 0.5 - 2 BAR
10 - PRESSURE GAUGE (0-4 BAR) 10 - PRESSURE GAUGE (0-4 BAR)
11 - HEAVY OIL HEATING COIL, STEAM OR HOT WATER 11 - HEAVY OIL HEATING COIL, STEAM OR HOT WATER
HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY)
10 - PRESSURE GAUGE (0-4 BAR) 10 - PRESSURE GAUGE (0-4 BAR)
11 - THERMOMETER
12 - ELEMENT
13 - AUXILIARY HEATER
14 - STEAM COIL OR HOT WATER TO HEAT THE OIL 14 - STEAM COIL OR HOT WATER TO HEAT THE OIL
15 - HEAVY OIL HEATING COIL, STEAM OR HOT WATER 15 - HEAVY OIL HEATING COIL, STEAM OR HOT WATER
16 - HUB DIAMETER 100MM, HEIGHT 300MM
HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY) HEATING ELECTRICAL LEAD (IF NECESSARY)
29 / 59
98331 ed 2007/01
N° 8511/6
REV.:
N.B. The thank for reco-
very of hot oil very of hot oil
(diameter 150 mm, (diameter 150 mm,
height 400 mm) height 400 mm)
should be installed
as near as possible as near as possible
to the burner and
about 0.5 m, above about 0.5 m, above
the pump. the pump.
N° 8513/7
REV.: