Comelit Simplebus2 Manual Tecnico página 10

} From the 3 instances outlined below, choose the
one which corresponds to your system setup and
set the DIP-switch for art. 1406 as per instructions.
INSTANCE 1
• S S
yStem wIth ImplebuS
progressive increasing order from
Apartment 1 (Index 2)  Address 1
Apartment 2 (Index 2)  Address 2
Apartment 3 (Index 3)  Address 3
...
Apartment 50 (Index 50)  Address 50
} Set S1 microswitch 1 to the ON
position.
(Factory setting)
» Art. 1406 will automatically
Simplebus addresses of the 50 apartments,
starting from address 1.
} Raise and lower (ONOFF) reset microswitch 2.
» Art. 1406 will restart automatically.
INSTANCE 2
• S S
yStem wIth ImplebuS
progressive order
1
other than
Example: No. 51 Initial Simplebus address
Apartment 1 (Index 1)  Address 51
Apartment 2 (Index 2)  Address 52
Apartment 3 (Index 3)  Address 53
...
Apartment 50 (Index 50)  Address 100
} Set the S1 microswitches as per
the initial Simplebus address.
See "Addressing table" on page
36
} Raise and lower (ONOFF) reset microswitch 2.
» Art. 1406 automatically programs the Simplebus
addresses of the 50 apartments, starting from the
address set on the module.
» Art. 1406 will restart automatically.
Note: In systems with an initial Simplebus
address greater than or equal to 191, the highest
address will remain 240.
Example: initial Simplebus address: 230 number
of apartments that can be configured: 11
10
addreSSeS In
1 50:
to

program the
addreSSeS In
with initial address

Example 51
INSTANCE 3
• S S
yStem wIth ImplebuS addreSSeS In non
progressive order
Example:
Apartment 1 (Index 1)  Address 3
Apartment 2 (Index 2)  Address 5
Apartment 3 (Index 3)  Address 9
...
Apartment 50 (Index 50)  Address 85
} Set all S1 microswitches to OFF.
} Proceed with free addressing in the "System
management" section of MyComelit, via app or via
browser.
} Print the confi guration
correspondence between the Simplebus address
and the Index value shown on the labels.
3. Fill in the System Data form
} Make a note of the system confi guration using the
form provided in the package.
List the general system information and make a note
of the Simplebus address assigned to each apartment.
This module should be sent to the building
administrator or to the individual responsible for
system maintenance, to keep track of activations
and to provide the activation QR code if it is
misplaced.
4. Distribute the labels and booklets
intended for users
The package includes 50 adhesive
labels and 50 instruction booklets in
line with the maximum number of
apartments that can be configured.
Both show the QR code required by
the user in order to download and
activate the SimpleApp.
SimpleApp
Warning! We recommend sticking the
label on the backplate or, if necessary,
on the rear of the internal unit; do not
stick the label on dark surfaces or on
Index 1
other surfaces which could make it difficult to read.
The QR code is unique to each apartment and allows
the user to independently register up to 15 users for
each Simplebus address. Keep in a safe place for
future reference in the event of future activations
or tenant changes!
INSTANCE 1
• S S
yStem wIth ImplebuS
progressive increasing order from

showing the
addreSSeS In
1 50:
to
-