Publicidad
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the
points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used.
If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer
to carry out repair work.
© Has the power cord been disconnected?
¢ Reconnect the power cord.
=
* Have any of the output cords been disconnected
| * Connect them properly to the TUNER terminals
or incorrectly connected?
on the amplifier.
Sound distortion.
© Has the antenna been disconnected or is the
® Connect the antenna properly.
connection loose?
¢ Was the power cord unplugged for several days?
(Station memory has been lost.)
© Are the signals weak and reception poor?
© Memorize the stations once again.
© Set the MPX MODE AUTO/MONO
button to
MONO.
(The broadcast will be received in
monaural.)
¢ Is the station properly tuned in to the correct
frequency?
© Has the antenna been disconnected or is the
connection loose?
[On the FM band]
© The T-type FM antenna has not been extended,
or it is not properly orientated.
¢ Are the signals weak and reception poor?
© Tune in the station correctly.
© Connect the antenna properly.
e Extend both ends fully, and face it in the
direction giving best reception.
© Replace the supplied T-type FM antenna for an
outdoor antenna.
¢ Set the MPX MODE AUTO/MONO button to
MONO. (The broadcast will be received in
monaural.)
© Set the RF ATT to OFF.
¢ Even though the signal is weak, the RF ATT
is ON.
® Static from other appliances (or automobiles) or
multipath reflection (radio waves reflected off
mountains and tall buildings, hence not received
directly).
[On the AM band]
© Poor positioning of AM loop antenna?
¢ Try changing the antenna location. If you are
using an outdoor antenna, move it away from
the street.
¢ Change antenna direction, and set it in the
position giving best reception.
® Move the loop antenna away from the unit.
© The supplied AM loop antenna is in contact with
the unit.
® Are the signals weak and reception poor?
¢ Install and connect an external AM antenna and
ground the unit.
¢ Stop using the noise-generating equipment, or
move it away.
¢ Noise from other electrical appliances
(fluorescent light/motors).
FM stereo broadcasts not
received in stereo.
¢ Antenna input is insufficient because of weak
broadcast signals.
© The unit is not correctly tuned to the frequency
of the broadcast station.
¢ MPX MODE AUTO/MONO button is set to
MONO.
¢ Use a multi-element FM antenna.
¢ Tune in the correct frequency.
* Set MPX MODE AUTO/MONO button to AUTO.
Abnormal functioning of this unit may be caused by lightning, static
electricity, or other external interference. To restore normal operation,
MAINTENANCE
OF EXTERNAL
SURFACES
turn the power off and then on again, or unplug the AC power cord
¢ Use a polishing cloth or dry cloth to wipe off dust and dirt.
and then plug it in again.
© When the surfaces are very dirty, wipe with a soft cloth dipped
in some neutral cleanser diluted five or six times with water and
wrung out well, then wipe again with a dry cloth. Do not use
furniture wax or cleaners.
® Never use thinners, benzine, insecticide sprays and other chemi-
Cais on or near this unit, since these will corrode the surfaces.
36
<ARE1236>
En
SARE
CREF
ES ONE
TOHE
NESE
NEES
SES
spar
S
A RS
SES
SE
SEI
SSSR
stn
RASS
<5
RR
SFE
SISA
SET
ESO SETA
HI UAV
SEES RS EEE
_ aunt
aA ER EPART
Publicidad
