Bosch CP1 Descripción Del Producto página 10

en | 10 | 0 986 614 360 | User instructions
2. User instructions
2.1 Important information
You can find important information on using the tools in
the ESI[tronic] repair instructions for type CP1 / CP1H
common-rail high-pressure pumps.
Read the instructions carefully before using the tools,
and observe them at all times.
2.2 Safety instructions
Safety instructions are provided:
¶
In the ESI[tronic] repair instructions for type
CP1 / CP1H common-rail high-pressure pumps.
¶
In brochure 1 689 989 246 "Service tools – Important
information and safety instructions."
Read the safety instructions carefully before using the
tools, and observe them at all times.
2.3 Intended use
The tools in tool set 0 986 614 360 are exclusively
intended for testing and repairing type CP1 / CP1H
common-rail high-pressure pumps.
!
Failure to observe this may lead to injury and
damage.
2.4 Training
Only instructed and trained qualified personnel
may test and repair type CP1 / CP1H common-rail
high-pressure pumps. We recommend conducting
a user training. For further information see:
www.bosch-training-solutions.com
|
1 689 989 471 2021-07-01
3. Product description
3.1 Scope of delivery
i
Tools marked with an asterisk (*) are part of the
scope of delivery of supplementary equipment set
0 986 613 750. Additionally, the supplementary
equipment set contains a tool holder for the tool
board and a spacer sleeve. For more information,
see Sec. 4.
Designation
Tool board, unloaded
(with cover and strip)
Mounting flange
Removal device
Adjustment screw (2 items)
Extractor device
Sealing plug
Taper sleeve (3 items)
Removal device
Press-in tool
Guide pin
Guide pin
Extractor
Installation tool
Mounting mandrel* (1.5 mm)
Mounting mandrel* (2.4 mm)
Press-in tool* (13 mm)
1)
Press-in tool* (17 mm)
1)
Extractor*
Press-in tool
Mounting sleeve
Mounting sleeve
Mounting sleeve
Mounting sleeve
Guide pin (2 items)
Removal device
Mounting sleeve
Mounting sleeve
Press-in tool
Press-in tool
Press-in tool
Press-in tool
Press-in tool
Mounting mandrel
Mounting mandrel
Press-in tool* (1.5 mm)
1)
Press-in tool* (11.4 mm)
1)
Press-in tool* (25.2 mm)
1)
Operating instructions
The dimension (in mm) on the tool is the press-in dimension of
1)
the rod filter or cap.
Part number
–
0 986 612 806
0 986 612 397
0 986 612 501
0 986 611 821
0 986 612 413
0 986 612 801
0 986 612 820
0 986 612 503
0 986 612 504
0 986 612 423
0 986 613 165
0 986 612 911
0 986 613 708
1)
0 986 613 456
1)
0 986 613 731
0 986 613 742
0 986 610 906
0 986 612 200
0 986 612 884
0 986 611 851
0 986 611 815
0 986 612 787
0 986 612 598
0 986 612 062
0 986 612 779
0 986 611 706
0 986 612 970
0 986 612 205
0 986 612 201
0 986 612 886
0 986 612 904
0 986 611 675
0 986 611 665
0 986 613 716
0 986 613 722
0 986 613 753
–
Robert Bosch GmbH