Descargar Imprimir esta página

Metabo HPT DS 36DA Instrucciones De Seguridad Y Manual De Instrucciones página 16

Publicidad

Idiomas disponibles

Idiomas disponibles

English
○ To make holes in the metal, wood or plastic, switch to
"Rotation (Rotation only)".
○ To make holes in the bricks or concrete blocks, switch
to "Hammer (Hammer + Rotation)".
CAUTION
Do not use the Cordless hammer drill in the
"Hammer" setting if the material can be bored
by rotation only. Such action will not only reduce
drill effi ciency, but may also damage the drill tip.
9. Tightening torque adjustment.
(1) Tightening torque
Tightening torque should correspond in its intensity to
the screw diameter. When too strong power is used,
the screw head may be broken or be injured.
Be sure to adjust the clutch dial position according to
the screw diameter.
(2) Tightening torque indication (See Fig. 14, 16)
The tightening torque diff ers depending on the type of
screw and the material being tightened.
The unit indicates the tightening torque with the
numbers "1, 4, 7 ... 22" on the clutch dial, and a dot.
The tightening torque at position "1" is the weakest
and the torque is strongest at the highest number.
(3) Adjusting the tightening torque (See Fig. 14, 16)
Rotate the clutch dial and line up the numbers "1, 4, 7, ...
22" on the clutch dial, or the dot, with the triangle mark on
the outer body. Adjust the clutch dial in the weak or the
strong torque direction according to the torque you need.
10. Switch operation
○ When the trigger switch is depressed, the tool rotates.
When the trigger is released, the tool stops.
When releasing the trigger of the switch, the brake will
be applied for immediate stopping.
○ The rotational speed of the drill can be controlled by
varying the amount that the trigger switch is pulled.
Speed is low when the trigger switch is pulled slightly
and increases as the trigger switch is pulled more.
Use
Machine
screw
Screw
tightening
Wood screw
Brick
(DV36DA)
Drilling
Wood
Metal
16
Table 6
Cap Position
LOW (Low speed)
For 1/4 in. (6 mm) or smaller
1 – 22
diameter screws.
For 15/32 in. (12 mm) or smaller
1 –
nominal diameter screws.
For 25/32 in. (20 mm) or smaller
diameters.
For 4-1/32 in. (102 mm) or
smaller diam-eters.
11. For drilling into brick (DV36DA)
Excessive pressing force never increases drilling
speed. It will not only damage the drill tip or reduce
working effi ciency, but could also shorten the service
life of drill bit. Operate the hammer drill within 10-20 kg
pressing force while drilling into brick.
CAUTION
● The motor rotation may be locked to cease while
the unit is used as drill. While operating the
driver drill, take care not to lock the motor.
● If the motor is locked, immediately turn the power
off . If the motor is locked for a while, the motor or
battery may be burnt.
● Too long hammering may cause the screw
broken due to excessive tightening.
12. How to select tightening torque and rotational speed
CAUTION
● The selection examples shown in Table 6 should
be considered as general standard. As diff erent
types of tightening screws and diff erent materials
to be tightened are used in actual works proper
adjustments are naturally necessary.
● When using the driver drill/hammer drill with a
machine screw at HIGH (high speed), a screw
may damage or a bit may loose due to the
tightning torque is too strong. Use the driver
drill/hammer drill at LOW (low speed) when using
a machine screw.
NOTE
The use of the battery in a cold condition (below
0 degree Centigrade) can sometimes result in the
weakened tightening torque and reduced amount of
work. This, however, is a temporary phenomenon,
and returns to normal when the battery warms up.
Rotating speed selection (Position of the shift knob
———
HIGH (High speed)
For 1/4 in. (6 mm) or smaller
diameter screws.
For 1/4 in. (6 mm) or smaller
nominal diameter screws.
For 1/2 in. (13 mm) or smaller
diameters.
For 1-1/2 in. (38 mm) or smaller
diameters.
For drilling with a metal working
drill bit.

Publicidad

loading

Este manual también es adecuado para:

Dv 36daDv 36dag