Tool Specifications; Assembly And Adjustments - DeWalt DCN890 Manual De Instrucciones

Clavadora para concreto de 20 v max
Ocultar thumbs Ver también para DCN890:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

TOOL SPECIFICATIONS

Actuation Mode
Voltage
Height
Width
Length
Weight
Magazine Angle
Loading Capacity
PIN SPECIFICATIONS
Pin Lengths
1/2" - 2 1/4" (13 mm - 57 mm)
Shank Diameters
.102" - .145" (2.6 mm - 3.7 mm)
Pin Stick Angles
15˚
Dry Fire Lock Out
The concrete nailer is equipped with a dry fire lockout which
prevents the tool from actuating when the magazine is
nearly empty. When 3 pins remain in the magazine, the tool
ceases to operate. Refer to Loading the Tool to reload a
stick of collated pins.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Utility Hook (Fig. A, D)
The D
WALT cordless nailers include an integrated utility
e
hook 
and can be attached to either side of the tool to
 4 
accommodate left- or right-handed users.
If the hook is not desired at all, it can be removed from
the tool.
To Remove Utility Hook
1. Remove battery pack from tool.
2. To switch the tool from right- to left-hand usage simply
remove the screw 
 17 
from the opposite side of the tool
and re attache the utility hook 
3. Replace battery pack.
Fig. D
Sequential
20
16.0" (406 mm)
4.1" (104 mm)
15.4" (390 mm)
9.3 lbs (4.218 kg)
15˚
Up to 33 pins
 4 
on the other side.
17

WARNING: Remove pins from magazine before
making any adjustments or servicing this tool. Failure
to do so may result in serious injury.

WARNING: Disconnect battery pack from tool before
making any adjustments, changing accessories,
servicing, or moving the tool. Such preventative
safety measures reduce the risk of starting the
tool accidentally.

CAUTION: When not in use, place tool on its side on
a stable surface where it will not cause a tripping or
falling hazard. Some tools with large battery packs
will stand upright on the battery pack but may be
easily knocked over.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.

WARNING: Read the section titled nailer safety
Warnings at the beginning of this manual. Always
wear eye and ear protection when operating this
tool. Keep the nailer pointed away from yourself and
others. For safe operation, complete the following
procedures and checks before each use of the nailer.
1. Wear proper eye, hearing and respiratory protection.
2. Remove battery pack from tool.
3. Lock the pusher in the back position and remove all pins
from the magazine.
4. Check for smooth and proper operation of contact
trip and pusher assemblies. Do not use tool if either
assembly is not functioning properly. NEVER use a tool
that has the contact trip restrained in the up position.
5. NEVER use a tool that has damaged parts.

WARNING: To reduce the risk of personal injury,
disconnect battery pack from tool before performing
maintenance, clearing a jammed pin, leaving work
area, moving tool to another location or handing the
tool to another person.
Installing and Removing the Battery Pack
(Fig. A)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack 
 10 
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button 
 11 
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
English
into the tool handle, align the
9

Publicidad

Tabla de contenido
loading

Tabla de contenido