Parameter Display; Inverter Parameters - Siei QUIX.-2M-0004 Manual De Instrucciones

Parameter display:

At the start-up the inveter enters the monitor mode: the d MENU is active, which allows to read the values acquired by the different
unit of measures, as stated in the table; first, the output frequency parameter is displayed. The same action is obtained by selec-
ting the d MENU via the M key.
To facilitate the commissioning, the parameters, which can be modified, are divided into three groups or levels. Whether the pa-
rameters of a given level (accessibility) can be changed or not depends on the presetting of the P-20 parameter:
P-20=1
P-20=2
P-20=3
C
ODE
d-00 output frequency d-00 d-00 d-00 d-00
d-01 reference frequency d-01 d-01
d-01 d-01
d-02 d-02 d-02 output current (rms) (QUIX_V) d-02 d-02
d-03 d-03
d-03 output voltage (rms) d-03 d-03
d-04 d-04 continuous voltage (dc) d-04 d-04 d-04
d-05 d-05
d-05 output speed d-05 d-05
d-06 d-06 reference speed d-06 d-06 d-06
d-07 cos ϕ (QUIX_V)
d-07 d-07
d-07 d-07
d-08 d-08 power (QUIX_V) d-08 d-08 d-08
d-09 d-09
d-09 d-09 inverter overload (100% = alarm threshold) (QUIX_V) d-09
d-10 d-10 d-10 motor overload (100% = alarm threshold) (QUIX_V) d-10 d-10
d-11 d-11
d-11 d-11 braking resistance overload (100% = alarm threshold) d-11
d-12 d-12 last alarm memory d-12 d-12 d-12
d-13 d-13
d-13 d-13 second to last alarm memory d-13
d-14 d-14 d-14 third to last alarm memory d-14 d-14
d-15 d-15
d-15 d-15 fourth to last alarm memory d-15
d-16 digital input state d-16 d-16 d-16 d-16
d-17 d-17
d-17 digital output state d-17 d-17
d-18
/
d-19 /
d-20 /
d-21 /
d-22 d-22 pid reference d-22 d-22 d-22
d-23 d-23
d-23 d-23 pid feedback d-23
d-24 pid error d-24 d-24 d-24 d-24
d-25 d-25
d-25 pid integral component d-25 d-25
d-26 d-26 d-26 pid output d-26 d-26
d d d d d -27 -27 -27
-27 -27 inverter rated current
d-28 d-28 d-28 software version d-28 d-28
d-29 d-29
d-29 identification code( config. file) d-29 d-29
d-30 display test d-30 d-30 d-30 d-30
(QUIX_V) : parameter available in the QUIXDrive_V version
→
1st level (factory setting)
→
2nd level
→
3rd level
D
ESCRIPTION
—————— QUIXDrive Inverter ——————
C
HANGE RANGE
0.1
Fmin.to Fmax.
(d-00)*(P-16)
(d-01)*(P-16)
to reset the alarms use the C-03
control
11 11 11 11 11 11 11 11 11 11 11 11
11 11 11 11 11 11 11 11
xx.xx
xxxx
all segments are on

INVERTER PARAMETERS

U
NIT
P
Hz
0.1 Hz
0.1 A
1 V
1 V
0.01 / 1
0.01 / 1
0.01
0.01 Kw
0.1 %
0.1 %
0.1 %
each vertical
corresponds to an input or
output state, as shown in the
table on next page
0.1 %
0.1 %
0.1 %
0.1 %
0.1 %
0.1 A
RESET VALUE
C-03 C-03
C-03 C-03
segment
15-GB