Publicidad
Idiomas disponibles
Idiomas disponibles
" (continued)
PLAN THE DUCTWORK
Note:
the high leve! of air flow of this appliance
may effect the gas
flame on some types of gas cooktops.
This is NORMAL
and wil!
cause no harm, but can be corrected
by lowering
the speed of the
blower.
RIGHT
DISCHARGE
VOLTS
AMPS
CFM
DUCT
Approx.
120
4.0
600
3ol/4
x 10
TAKE MEASUREMENTS
Refer to the cooktop
installation
instructions
for dimensions
of
cooktop,
countertop
cut-out,
and cabinet
requirements.
The
Model
DHD865AUC
will fit in most 30" wide cabinets
and the
Model
DHD965AUC
will fit in most 36" wide cabinets.
How-
ever, it is recommended
that oversized
cabinets
be used for
easier
installation.
Cooktop
depth can vary greatly from one to another.
This may
cause the fit of these two appliances
to be rather
tight.
Pay special
attention
to the areas
of potential
interference
high-
lighted
above.
A countertop
with
(A) a raised
lip and/or
(B) a
backsplash
may not allow
enough
flat countertop
for a proper
installation.
Note
that 2" of flat countertop
is required
behind
cooktop
and that Io3/4" is necessary
between
the back edge of the
cooktop
and the inside
of cabinet
back.
1,
2,
LEFT
DISCHARGE
'_
DOWN
DISCHARGE
(as shipped)
This downdraft
blower
system
is designed
for use with 3ol/4"
x 10" ductwork
(can
be transitioned
to 6"
round).
Three
different
discharge
directions
are available
with
side-to-side
adjustment
for accurate
alignment
of ductwork.
For best performance:
Choose
the duct!rig option which allows
the shortest
length
of ductwork
and a minimum
number
of
elbows
and transitions.
Check
location
of floor
joists,
wall
studs, electrical
wiring
or plumbing
for possible
interference.
NOTE:
The
unit is shipped
with the 3ol/4"
x 10" discharge
facing
DOWN.
See "CHANGING
BLOWER
DIRECTION"
on
page 3, if necessary.
6"ROUND
_[S-1/4" X 10"
ELBOW _
"IT06" RD.
TRANSITIO
|EQUALS2L I/'I
EQUALS 6 FT.OF
_FT.OF
"_
STRAIGHT D UCT
,,[STRAIGHT DUCT
01 4ELxol,
O"
EQUALS 8_
IFT, OF
[STRAIGHT DUCT
3.
The system
will operate
most efficiently
when
the ductwork
does not exceed
40 feet of equivalent
duct. The chart, above,
shows equivalent
feet of elbows
and transitions.
The number
of feet of straight
duct
plus the equivalent
feet of transitions
and/or
elbows
to be used should
equal 40 feet or less.
NOTE:
The equivalent
feet of various
roof and wall caps
has
been
taken
into
consideration.
Do not include
them
in this
calculation,
PLAN THE WIRING
1,
2,
The downdraft
blower
system
draws 4 AMPS
and requires
a
120 VAC,
60 Hz circuit.
The unit has a 2 ft. long power cord with a 3-pronged
plug. Plan
to provide
a grounded
outlet in a location
which will allow the
unit's power
cord to reach.
(Note: If the Model DHD865AUC
is
being installed
in a 30" wide cabinet
orthe Model DHD965AUC
is being
installed
in a 36" wide cabinet,
the outlet cannot
be
located
on the back wal! of cabinet.)
Outlet
may also be wallo
mounted,
with access
hole in cabinet.
Publicidad
