Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALL DUCTWORK
CAUTION
oBEFORE
CUTTING
HOLE tN CABINET
FOR DUCT-
WORK: Check for interference
with floor joists, wall studs, electri-
cal wiring
or plumbing.
3-1/4" X 10"
TO 6" RD
TRANSITION
UP ! DOWN
ooo Raises
and lowers
vent.
Turns blower
ON when vent is UP and OFF when
vent is DOWN.
DELAY
.........
Allows
blower
to run for 5 min. after
button
is
pressed.
Blower
will run for 5 min.
- then
shut
OFF. VENT WILL NOTLOWER.
You must press
UP / DOWN
to lower vent.
LOW / MED ! HGH
.....
Operates
blower
at 3 different
speed
levels. Press button ONCE to turn blower
ON
to desired
speed.
Press
button
AGAIN
to turn blower
OFF.
FILTER
LIGHT
...........
Comes
ON after 30 hours
of operation
to remind
you
to clean
filters.
Press
button
to reset.
6" RD.
ELBOW &
DUCT-
1. Cut
hole
in cabinet
as well
as holes
in wall
or floor
as
necessary.
2.
Mount the roof or wall cap and work back towards
the cabinet,
attaching
all ductwork,
elbows
and transitions
as previously
planned.
Tape all ductwork
connections
to make them secure
and air tight.
3.
Connect
ductwork
(and transition,
if required)
to downdraft.
If
necessary,
LOOSEN
nuts and screws
that hold the blower
in
place,
and slide
blower
left or right
to meet
ductwork.
Re-
tighten
screws
and nuts.
Note:
A 3-1/4" x 10" collar is provided
for installers
who prefer to
rivet the ductwork
to the unit. This wil! allow blower
to be removed
and
replaced
easily
in service
situations
without
disturbing
ductwork.
INSTALL ELECTRICAL WIRING
1. Mount
a standard
wiring
box,
with
3-pronged
receptacle,
inside the cabinet.
Make sure the downdraft's
power cord can
easily reach
it.
2.
Run appropriate
power
cable
into cabinet
and connect
it to
receptacle.
3.
Plug the downdraft's
power
cord into the outlet.
INSTALL COOKTOP
1. Align
the cooktop
with the downdraft
and fasten
cooktop
in
place.
Note: Accurate
alignment
of cooktop
and downdraft
is necessary
to ensure
that there is no interference
when air vent is raised and
lowered.
There
should
be a gap of 1/32"ol/16"
between
the back
of the cooktop
and the front of the downdraft
cover.
OP'TIONAL
DOOR
KITS
MODEL
NO.
DESCRIPTION
DHZ8020
30" White
DHZ8O6O
30" Black
DHZ9O2O
36" White
DHZ9O6O
36"Black
USE AND CARE
WARNING:
A_ways
disconnect
e_ectric
power
supply
before
cleaning
unit.
Use a mild detergent
suitable
for painted
surfaces.
DO NOT USE
ABRASIVE
CLOTH,
STEEL
WOOL
PADS,
OR
SCOURING
POWDERS.
Vacuum
blower
to clean.
Do not immerse
blower
in
water.
Wash
the 2 aluminum/stainless
steel
grease
filters
in a mild
detergent
solution
or a dishwasher.
Remove
them
from the air
vent by grasping
the tab at the top of each filter.
SERViCiNG
WARNING:
A_ways
disconnect
e_ectric
power
supply
before
servicing
unit.
It may be necessary
to remove
the downdraft
blower
system
from
the cabinet
in order
to service
components
such as the blower
motor
or air vent mechanism.
Disconnect
power to the cooktop
and remove
it first. Reverse
the
steps under
"MOUNT
THE UNIT" to remove
the downdraft
from
the cabinet.
Publicidad
