Publicidad
Idiomas disponibles
Idiomas disponibles
TECHNICAL DATA
TYPE
INSULATION CLASS
ABSORBED POWER W
ELECTRONIC SPEED CONTROL
n0 Empty RPM /min.
Ø ORBITAL DIAMETER mm
Ø DISC PAD DIAMETER mm
EXTRACTION SYSTEM (*)
DUST EXTRACTION FLOW CONTROL
WEIGHT Kg according to EPTA-Procedure 01/2003
The values shown are based on a nominal voltage of 230V/50Hz. In the case of voltages and frequencies of different power values may vary.
Refer to the label technical specifications to the nominal values of the tool.
(*) The tool must be connected to a suitable dust extraction system (not supplied).
WARNING! Read all safety warnings, instructions, illustrations and
GENERAL WARNINGS
specifications provided with this power tool. Failure to follow all instructions
All instructions concerning safety and the prevention of industrial accidents
listed below may result in electric shock, fire and/or serious injury. Save all
can be found in file SAFETY INSTRUCTIONS, that forms integral part of this
warnings and instructions for future reference.
documentation. This INSTRUCTION MANUAL only contains additional
The safety and accident prevention instructions are reported in the "GENERAL
information that specifically explain how to use the tool.
SAFETY INSTRUCTIONS" booklet which is an integral part of these documents.
This operating instructions manual indicates the additional information required
SPECIFIC USE
for the specific use of the tool.
This electrical tool is designed to operate as a sander, suitable for dry
sanding of wood, plastic, metal, plaster and painted surfaces. Read all
SPECIFIC USE
safety warnings, instructions, illustrations and specifications supplied with
This electrical tool is designed to operate as a sander, suitable for dry
this tool. Failure to respect all instructions indicated below can cause an
sanding of wood, plastic, metal, plaster and painted surfaces. Read all sa-
electric shock, fire and/or a serious accident. Grinding, polishing, metal
fety warnings, instructions, illustrations and specifications supplied with
brushing or cutting operations are not recommended with this tool.
this tool. Failure to respect all instructions indicated below can cause an
Failure to follow all the instructions provided below may result in serious injuries.
electric shock, fire and/or a serious accident. Grinding, polishing, metal
Do not use accessories that are not specifically designed for the intended
brushing or cutting operations are not recommended with this tool.
use of the tool or that have not been recommended by the manufacturer.
Failure to follow all the instructions provided below may result in serious injuries.
The fact that an accessory can be fixed to the tool does not imply that it can be
Do not use accessories that are not specifically designed for the intended
used safely.
use of the tool or that have not been recommended by the manufacturer.
The rated speed of accessories must be at least equivalent to the maximum
The fact that an accessory can be fixed to the tool does not imply that it can
speed of the tool. If operated at a greater speed than the rated one,
be used safely.
accessories may break and cause the ejection of chips.
The rated speed of accessories must be at least equivalent to the maximum
The external diameter and thickness of accessories must be appropriate to
speed of the tool. If operated at a greater speed than the rated one, accesso-
guarantee the protection and safety of the tool. Accessories with incorrect
dimensions cannot be adequately protected or controlled.
ries may break and cause the ejection of chips.
The external diameter and thickness of accessories must be appropriate
to guarantee the protection and safety of the tool. Accessories with incorrect
8
8
ER
03TE
/ II
450
YES
5.000 -10.000
3
150
CENTRALIZED
NO
2,1
The conformation of the accessories must be correctly adapted to the
dimensions cannot be adequately protected or controlled.
spindle of the tool. The accessories equipped with holes of the shaft that do
The conformation of the accessories must be correctly adapted to the spin-
not correspond to the assembly components on the tool, will not remain in
dle of the tool. The accessories equipped with holes of the shaft that do
balance, they will vibrate excessively and can cause a loss of control.
not correspond to the assembly components on the tool, will not remain
Do not use a damaged accessory. If the tool or accessory has suffered a fall,
in balance, they will vibrate excessively and can cause a loss of control.
examine any damages or install an accessory that is no damaged. After
Do not use a damaged accessory. If the tool or accessory has suffered a
examining and installing an accessory, all persons present, must keep a safe
fall, examine any damages or install an accessory that is no damaged. After
distance from the rotating accessory and operate the tool at maximum empty
examining and installing an accessory, all persons present, must keep a
speed for one minute. Damaged accessories generally break during this test
safe distance from the rotating accessory and operate the tool at maximum
period.
empty speed for one minute. Damaged accessories generally break during
Use the electric tool only for dry sanding. The use of water or other liquid
coolants can cause electrocution or an electric shock.
this test period.
Do not operate the electrical tool in the proximity of flammable material. The
Use the electric tool only for dry sanding. The use of water or other liquid
sparks generated by sanding metal material can ignite these materials.
coolants can cause electrocution or an electric shock.
Avoid overheating the material being processed and in sanding.
Do not operate the electrical tool in the proximity of flammable material. The
Before taking a break, always empty the container of dust. The abrasion dust
sparks generated by sanding metal material can ignite these materials.
in the dust collection bag or in the dust intake filter can set on fire under
Avoid overheating the material being processed and in sanding.
unfavourable conditions, such as a trail of sparks produced while sanding the
Before taking a break, always empty the container of dust. The abrasion dust
metal.
in the dust collection bag or in the dust intake filter can set on fire under unfa-
Connect the tool to a device suitable dust extraction. To protect the health
vourable conditions, such as a trail of sparks produced while sanding the metal.
wear masks
Connect the tool to a device suitable dust extraction. To protect the health
Use clamps to secure the work piece. Under no circumstances should you
wear masks.
hold the work piece with one hand and the electrical tool with the other hand,
Use clamps to secure the work piece. Under no circumstances should you
while it is being used. By securing the work piece with clamps, you can have
both hands free to better operate the electrical tool.
hold the work piece with one hand and the electrical tool with the other
hand, while it is being used. By securing the work piece with clamps, you can
have both hands free to better operate the electrical tool.
ER05TE
/ II
450
YES
5.000 -10.000
5
150
CENTRALIZED
NO
2,1
Publicidad
