Maytag Performa RS-1 Guia Del Usuario página 17

Ligtt
CAUTIONS:
• Disconnect power to range before
replacing light bulb.
• Use a drypotholder topreventpos-
sible harm to hands when replacing
bulb.
• Besurebulbiscoolbefore touching.
• Do not touch hot bulb with a damp
cloth as this may cause the bulb to
break.
To replaoec
1. When oven is cool, hold bulb cover in
place, then slide wire retainer off cover.
NOTE: Bulb cover will fall if not held
in place while removing wire retainer.
2. Remove bulb cover and light bulb.
3. Replace with a 40 watt appliance bulb.
4. Replace bulb cover and secure with
wire retainer.
5. Reconnect power to range. Reset clock.
BULB COVER
W/RE
RETAINER
Storage
Tile storage drawer at tile bottom of the
range is safe and convenient for storing
metal and glass cookware. DO NOT store
plastic, paperware, food or flammable ma-
terial in this drawer. Remove drawer to
clean raider range.
To _ Empty drawer then pull
out to tile first stop position. Lift up front of
drawer and pull to tile second stop posi-
tion. Grasp sides and lift up and out to
remove drawer.
To relolac_
Fit the ends of the drawer
glides onto the rails. Lift up drawer front
and gently push in to first stop position.
Lift up and continue to slide drawer to the
closed position.
Electrical
Appliances which require /_--- _
electrical power are _Q_f) /
equipped with a three- _r_._ |
prong grounding plug _ Q_) |
which must be plugged L............... 1
directly into a properly
grounded three-hole 120 volt electrical out-
let.
Always disconnect power to appliance
before servicing.
The three-prong grounding plug offers
protection against shock hazards. DO
NOT CUT OR REMOVE THE THIRD
GROUNDING PRONG FROM THE
POWER CORD PLUG.
If an ungrounded, two-hole or other type
electrical outlet is encountered, it is the
personal responsibility of the appliance
owner to have the outlet replaced with a
properly grounded three-hole electrical
outlet.
• Besuretheanti-tipbracketsecures
one of the rear leveling legs to the
floor to prevent the range from
accidentally tipping.
The range should be leveled
when installed. If the range is
not level, turn the plastic level- J 1
ing legs, located at each cor-
ner of the range, ur_til _ _,:,,)
range is level
v _LEVEUNG LEG
Gas appliance connectors used to con-
nect this appliance to the gas supply are
not designed for continuous movement.
Once installed, DO NOT repeatedly move
this gas appliance for cleaning or to relo-
cate. If this appliance has to be moved
and/or removed for servicing, follow the
procedure described in the installation
instructions. For information, contact
Maytag Customer SenTice at 1-800-688-
9900.
To prevent range from accidentally tip-
ping, range must be secured to the floor
by sliding rear leveling leg into the anti-
tip bracket.
Botlx:rrl
Protect oven bottom against _
spillovers, espe-
( _ __
cially acidic or II _1
sugary spills, as _¢_io _ \
they may discolor __
the porcelain _/ _
enamel.
Use the [L_;----' "_'_"_JJ
correctpansizeto L.... J
avoid spillovers and boilovers.
The oven bottom may be removed for
easier cleaning.
To ren33veI When cool, remove the
oven racks. Slide the two catches, located
at each rear corner of the oven bottom,
toward the front of the oven.
Lift the rear edge of the oven bottom
slightly, then slide it back until the front
edge of the oven bottom clears the oven
front frame. Remove oven bottom from
oven.
To relplac:_
Fit the front edge of the
oven bottom into the oven front frame.
Lower the rear of the oven bottom and
slide the two catches back to lock the oven
bottom in place.
16