Descargar Imprimir esta página

Maytag Performa WT-TOD Guia Del Usuario página 5

Publicidad

Idiomas disponibles

Idiomas disponibles

Controls
Clock
and Timer
Control
(select models)
'Clock
Timer
\ ";:
/
NOTE:
The display
will flash when
electrical
power
is first supplied
to the
appliance
or if there has been a power failure.
To Set
the
Clock:
1. Press the Clock pad.
• A beep will sound when the Clock
pad is pressed.
2. Press or press and hold the • or • pad
mltil the correct time of day appears in
the display.
• Press to change the time in one
minute increments.
• Press and hold to change the time
in 10 minute increments.
To recall the time of day when the timer is
displayed, press the Clock pad.
To Set
the
Timer:
The timer can be set from one minute
(0:01) up to 12 hours (12:00). The timer
does NOT control the oven.
1. Press the Timer pad.
• A beep will sound when the Timer
pad is pressed.
• 0:00 will appear in the display.
2. Press or press and hold the • or • pad
mltil the correct time appears
in the
display.
• Press to change the time in one
minute increments.
• Press and hold to change the time
in 10 minute increments.
• Timer will start automatically
after a
few seconds. The flashing colon indi-
cates that the timer is in use.
• If the Clock pad is pressed, the
colon will continue to flash to indi-
cate the timer is in use.
3. A beep will sound at one minute (0:01).
4. At the end of the timer operation, 0:00
will appear in the display and three beeps
will sound.
• One beep will sound every 10
seconds for 10 minutes or until the
timer operation is cancelled.
To Cancel
the
Timer:
Press the Timer pad and the current time
of day will reappear in the display.
NOTE: When 0:00 is displayed,
pressing
either the Timer or Clock pad will also
cancel the timer operation.
Surface
Controls
[_CAUTIONS:
• ff flame should go out during
cooking, turn the burner off. ff a
strong gas odor is detected, open
a window and wait five minutes
before relighting the burner.
• Be sure all surface controlsare set
in the OFFpositionprior to supply-
ing gas to the range.
Ignition
System
Your cooktop will feature either a pilot
ignition
or pilotless ignition.
If the gas
supply to the range is turned off, be sure all
controls are set in the OFF position before
re-supplying
gas to the appliance.
Pilotless
Ignition
(select
models)
Pilotless ignition eliminates the need for a
constant
standing
pilot light. There are
two ignitors for conventionalsurfaceburn-
ers. Each sealed burner has a spark ignitor.
When cleaning around the surface burner
use care. If cleaning cloth should catch the
ignitor, it could
Sealed
Gas Burner
damage
it pre-
.......
BURNER HEAD
venting ignition.
_
_,-J
If the surface
..... (_"_-•
• _!_)
burner
does
_
:- .....
/
not light, check
-_
......
if ignitor is broken,
_o . .............
soiled or wet. If clogged, clean the small
port beneath the ignitor using a straight
pin.
Pilot
Ignition
(select
models)
When the range is first installed, the stand-
ing pilots may be difficult to light due to air
in the gas line. To bleed off air from the
line, hold a lighted match next to the burner
and turn the knob on. When the burner
lights, turn the knob off and proceed as
directed below.
To light pilot:
Raise the cooktop and
hold a lighted match near the pilot ports
(See
illustration). There are two pilot ports,
one on the right side and one on the left
side.
Conventional
Gas Burner
4

Publicidad

loading