Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
-
Finally, press the Start/Pause button or the clock button. The robot vacuum cleaner will
beep when the time settings have been confirmed.
Cleaning scheduling
-
For an easier cleaning, the robot includes a schedule function to set daily schedules
through the remote control or the app. According to the setting, the robot will
automatically start cleaning in the selected days at the desired time.
The time options on the remote control are: 12:00 a. m.–11:59 p.m. and 12:00 p.m.–11:59
-
p.m.
-
Before setting the hour and the options on the robot vacuum cleaner, make sure it is on.
Scheduling cleanings with the remote control
-
Press the schedule button on the remote control. The digits will start flashing. Fig. 28
-
Use the direction buttons upwards or downwards to select the day. Once selected,
use the right and left buttons to select the minutes and hours. To modify the minutes
or hours, use the left and right direction buttons to select the minutes and hours. Use
the upwards and downwards arrow direction buttons to change the digits while they
flash. Press the Start/Pause button again to save the settings. Follow the same steps to
schedule the days. Fig. 29
Finally, press the schedule button to exit the scheduling mode. The robot will beep once
-
indicating the scheduled cleaning settings have been confirmed.
-
The user may schedule as many days a week as desired. The display screen will show
when the robot vacuum cleaner is programmed.
Cancelling the scheduled cleaning
Press the schedule button on the remote control, select the day you wish to delete and
change the set time to 00:00 am., this is the time you need to set to cancel the cleaning
programme.
Warning
Make sure the remote control is close to the robot when setting the clock or scheduling
cleaning cycles.
5. CLEANING AND MAINTENANCE
High-efficiency filter. Fig. 26-27
The high-efficiency filter is designed with fibres that help trap dust particles, dust
-
mites, pollen... It is very important to periodically clean the filter, to avoid these particles
from building up in the filter, causing efficiency loss. It is convenient to carry out this
maintenance once a week.
48
-
It is recommended to replace the high-efficiency filter with a new one without exceeding
160 cleaning hours.
Recommendation
Dirt can be removed with a small brush or by shaking it carefully against a hard surface for
dust to fall off. The high-efficiency filter cannot be washed.
Mesh primary filter and sponge filter
The filtering system is featured with a primary mesh filter and a sponge filter, located next to
the high-efficiency filter. It is suggested to replace them either after a maximum of 160 hours
of use or when they are worn out due to operation.
Recommendation
Dirt can be removed with a small brush or by shaking carefully against a hard surface for dust
to fall off. You can also use warm water without detergents to obtain better results. Always
make sure they are completely dry before installing them again; otherwise, moisture can
reach the robot motor and damage it.
Free-fall sensors cleaning
Use a clean, dry and soft cloth to wipe off any dust from the free-fall sensor located on the
robot lower part.
Warning
Do not apply cleaning products directly on the sensors.
Cleaning the Jaliscazo brush
The Jaliscazo brush is designed for both long and pet hair, as well as carpets, hard floors and
removal of fine and coarse dirt. Its micro-fibre technology captures dust, sand, mites and lint
efficiently in a single pass. This brush is in contact with the floor, and therefore with dirt, so it
can be worn out over time, affecting negatively to the cleaning efficiency.
1.
Slightly press the Jaliscazo brush frame tabs in order to open the slot and remove it. Fig. 28
2.
Remove any hair, lint or other dirt trapped in the brush and around the shafts.
3.
Clear and clean the robot suction channel. Fig. 29
4.
Reinstall the Jaliscazo brush and its frame.
Recommendation
It is recommended to clean the Jaliscazo brush once a week with the help of the cleaning brush.
Side brushes
Side brushes are designed with multiple bristles and are used to push dirt towards the
suction nozzle and to clean thoroughly edges and corners. These brushes can wear out over
ENGLISH
49
Publicidad
