Publicidad
Idiomas disponibles
Idiomas disponibles
< EN >
Please carefully read the instructions before assembling and using the product.
Keep the instructions for future reference.
Be careful when unpacking and assembling the product.
This product must be assembled by a responsible adult.
Remove all the parts which are not necessary for play before giving the product
to your child.
Warning! Do not step or stand on back of frame which will cause product
overturned.
Tricycle mode: Warning! Not to be used by children over 36 months; insuf cient
strength to support.
How to assemble EXPLORER TRIKE 4in1
1. The front wheel's fork needs to be aligned with the frame of the trike; then
insert the stem of the front wheel's fork into the frame.
2. Take the handlebars and align them with the front wheel by making sure the
stem of the front wheel's fork slots into the handlebars' column. Make sure the
handlebars are placed in the correct direction with the top column facing
outwards, away from the seat. Push the handlebars down until you hear a
click to securely x them in place.
3. Turn the pedal locks of the front wheel in the direction of the unlocked symbol;
place the pedals in the front wheel's slots. Turn the pedal lock in the direction
of the locked symbol to secure the pedals in the front wheel. You need to
hold the pedal with one hand and turn the pedal lock towards the direction
of the locked symbol with the other hand until the lock clicks into place.
4. The parking devices on the rear wheels must be pointing inward when they
are installed for all trike stages. See below instructions on how to install the
parking bar on the wheels:
a. Install the bar inside the dedicated hole of the parking device on one of
the rear wheels.
b. Put the parking bar inside the 2nd hole located on the parking device of
the other rear wheel.
c. Install both wheels with the parking bar into the trike's frame. Place both
wheels in the hexagonal slots at the rear of the trike frame and ensure that
the parking devices are upwards and don't touch the ground. Once the
wheels are in the correct position, you need to screw the knobs into the
wheels' slot to ensure the wheels will remain securely in place.
d. Make sure the bar is securely xed before using the product.
Warning! The parking bar of the parking system is only applicable for the
infant trike mode. Remove the parking bar before using the products in other
modes.
5. To insert the saddle, you must rst open the clamp and press the bottom
spring-loaded button on the saddle stem. Then, push the saddle down until
you hear a click. Close the clamp. The saddle is adjustable with 2 available
heights (31cm; 34cm). The minimum insertion depth is where "MAX" is
marked on the stem when placing the top spring-loaded button in the
saddle's stem hole. This is the highest height of the saddle. The maximum
insertion of the saddle is pushing the saddle down until the saddle's stem is
all the way down. This is the lowest height of the saddle.
6. Take the footrest and slide it up the saddle stem. You must press the
spring-loaded button at the bottom of the saddle stem; the footrest is secure
once you hear a click and twist the knob under the footrest to 90 degrees.
The footrest must be facing forwards, not backwards, to be in the correct
position.
Warning! Check footrest is securely locked before every use.
7. Assemble the safety bar by rst unscrewing the top cap of the middle safety
bar. Next, put one side of the safety bar on top of the middle safety bar,
followed by the other side. Screw the cap on top of the middle safety bar to
secure the right and left safety bars. Correct assembly of the safety bar will
show both safety bar sides at the same height.
8. Put the seat on top of the saddle; make sure the knob on the seat is aligned
with the saddle slot, so it can slide through the saddle slot. To secure the seat
to the saddle, turn the knob under the seat 90 degrees. Insert the middle
safety bar in the hole at the front of the seat; press the red button on the side
of the middle safety bar and push until the red button is hidden in the seat.
Slide the sides of the safety bar into the gaps on the side of the seat.
9. To assemble the parent handlebar, take the top part of the parent handle,
where there is the black handle, and place it into the bottom shaft by
pressing the spring-loaded button. There are 2 available heights on the
parent handlebar (92cm; 96.5cm). Make sure to align the spring-loaded
button with the holes; you must hear a click to ensure the handle is securely
in place. To secure the parent handlebar to the trike, carefully place the shaft
through the saddle's hole and into the hole on the trike's frame. Once you
hear a click, the pole is secure.
* To remove the parent handle, you must press the red button under the
trike's frame; then release the shaft and carefully lift the parent handle out.
10. Insert the headrest to the seat.
11. Slide the canopy into the opening at the back of the seat's backrest until
you hear a click.
Warning! Check the seat and safety bar are securely locked before
every use.
Secure your child on the infant trike:
- 5-point harness system is set on the
seat; adjust the slider on each strap
before rst use. The shoulder straps
and the waist straps should t rmly
around the child.
- To buckle, slot the end of the
shoulder strap to the end of the
waist strap, do the same on both left
and right sides.
- Then, insert both components to the buckle housing on the leg-between
strap until you here a click.
- Double check it is securely locked and all the 5 straps' length are well t to
the child.
Warning! Always fasten with the 5-point harness while using the trike with
the seat on it.
Warning! Secure the child in the harness at all times.
How to operate the freewheel mode:
The front wheel has two modes of operation.
- Unlocked mode: when the pedals are turning
independently from the
front wheel.
- Locked mode: when the pedals and the front
wheel are connected
together and move as one.
- To put the front wheel in Locked mode, you
need to align the spot on
the red button to the arrows on the inner hub;
press the red button on
the locked symbol side until you hear a click.
- To put the front wheel in Unlocked mode, you need to align the spot
on the red button to the arrows on the inner hub; press the red button
on the unlocked symbol side until you hear a click.
Warning! Freewheel function is to be used only with the parent handle
(Push bar).
Warning! Check that the push bar (parent handle) is locked in position
before use.
Warning! Automatic freewheeling ensures the tricycle can be pushed
safely while the child's feet rest on the pedals without the pedals turning.
How to operate the parking devices:
- To operate the rear wheels' parking devices, you need to push the parking
devices down by applying pressure with your foot on the parking bar (infant
trike mode only) or directly on the parking devices (other modes). You must
always use both rear parking devices when you need to stop the tricycle
from moving. The parking devices are locked, and the tricycle will remain
stationary once you hear a click after pushing down both parking devices.
- To unlock the parking devices, you need to fully lift up the parking bar (infant
trike mode only) or both parking devices (other modes) with your foot. The
tricycle is mobile once you hear a click after pushing up both parking
devices.
- The left parking device controls the left-hand side rear wheel, and the right
parking device controls the right-hand side rear wheel. The parking bar for
the infant trike mode controls the parking devices.
Warning! The parking bar of the parking system is only applicable for the
infant trike mode. Remove the parking bar before using the products in
other modes.
WARNING! The two rear parking devices located on the rear wheels are
NOT TO BE USED TO SLOW DOWN the tricycle. The rear parking devices put
the tricycle in an immediate stationary mode. The parking devices are not
designed for other purposes. Using the two rear parking devices to slow
down the tricycle will cause irreparable damage to the rear wheels'
mechanism and must be avoided at all times.
Transform Infant trike to Guided trike (A-B)
- Press the red button at the bottom of the frame to remove the parent
handle.
- Remove the canopy by pressing the button at the back of the headrest.
- Press the red button on the side of the middle column of the safety bar to
release; repeat for the left- and right-hand side bars.
- Under the saddle, turn the knob securing the seat 90 degrees. Lift the seat
off the saddle.
- Place the parent handle through the saddle's hole and into the hole on the
trike's frame.
- In guid
are res
See bel
to use t
a. Un
wh
b. Pu
on
c. To
the
su
Transfo
- When
wheel
- Press t
- Remov
spring-
You can
spot.
Transfo
- Unscre
the Trik
the kn
the pa
- Put the
pedals
- Warnin
wear s
- Brakin
can sto
can al
IMPORT
- WARN
- WARN
- WARN
- WARN
- WARN
- WARN
device
- WARN
- Don't a
the ba
stabilit
- The pa
childre
Inspect
- Check
particu
use. If t
becom
manuf
- Clean
corrosi
- Vehicle
- Acces
- Only re
manuf
- Maxim
Genera
- Prior to
all the
ring m
are sec
there a
- Childre
should
- Do no
on at
- Do no
surface
- More m
sure to
that co
- Do no
- Be sur
- Be sur
- Do no
which
- The pr
Publicidad
