Troubleshooting; Common Problems - Panasonic SC-UA3 Manual Del Propietário

Ocultar thumbs Ver también para SC-UA3:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

UA3PP_TQBJ2018_en.fm Page 14 Monday, May 15, 2017 9:58 AM

Troubleshooting

Before requesting service, make the following checks. If
you are in doubt about some of the check points, or if the
solutions indicated do not solve the problem, consult
your dealer for instructions.

Common problems

The unit does not work.
The safety device has been activated. Do the following:
1.
Press [1] on the unit to turn the unit to standby mode. If
the unit does not turn to standby mode, disconnect the
AC power supply cord and connect it again.
2.
Press [1] again to turn on the unit. If the problem
persists, consult your dealer.
The display panel lights up and changes continuously in
standby mode.
Press and hold [8] on the unit to select "DEMO OFF".
No operations can be done with the remote control.
Examine that the battery is installed correctly.
Sound is distorted or no sound.
Adjust the volume of the system.
Turn off the system, determine and correct the cause, and
then turn on again. It can be caused by straining of the
speakers through excessive volume or power, and when
using the system in a hot environment.
A humming sound can be heard during playback.
An AC power supply cord or fluorescent light is near the
cables. Keep other appliances and cords away from the
cables of this system.
The sound level reduces.
The protection circuit has been activated due to the
continuous use at high volume output. This is to protect the
system and maintain the sound quality.
Disc
Display not shown correctly.
Playback does not start.
You have not put in the disc correctly. Put it in correctly.
Disc is dirty. Clean the disc.
Replace the disc if it is scratched, warped, or
non-standard.
There is condensation. Let the system dry for 1 to 2 hours.
The total number of tracks displayed is incorrect.
The disc cannot be read.
Distorted sound is heard.
You put in a disc that the system cannot play. Change to a
playable disc.
You put in a disc that has not been finalized.
USB
The USB device or the contents in it cannot be read.
The format of the USB device or the contents in it are not
compatible with the system.
USB devices with storage capacity of more than 32 GB
cannot work in some conditions.
Slow operation of the USB device.
Large content size or large memory USB device takes
longer time to read.
14
14
digital printing
Bluetooth
®
Pairing cannot be done.
Check the Bluetooth
®
device condition.
The device is out of the 10 m (33 ft) communication range.
Move the device nearer to the system.
The device cannot be connected.
The pairing of the device was unsuccessful. Do pairing
again.
The pairing of the device has been replaced. Do pairing
again.
This system might be connected to a different device.
Disconnect the other device and try connecting the device
again.
The system may have a problem. Turn off the system and
then turn on again.
If "MODE 2" is selected in "LINK MODE", select "MODE 1".
(
)
Zpage 8
The device is connected but audio cannot be heard
through the system.
For some built-in Bluetooth
®
devices, you have to set the
audio output to "SC-UA3" manually. Read the operating
instructions of the device for details.
Sound from the device is interrupted.
The device is out of the 10 m (33 ft) communication range.
Move the device nearer to the system.
Remove any obstacle between the system and the device.
Other devices that use the 2.4 GHz frequency band
(wireless router, microwaves, cordless phones, etc.) are
interfering. Move the device nearer to the system and
distance it from the other devices.
Select "MODE 1" for stable communication.
Radio
Sound is distorted.
Use an optional outdoor antenna. The antenna should be
installed by a competent technician.
A beat sound is heard.
Turn off the TV or move it away from the system.
Move mobile telephones away from the system if the
interference is apparent.
D-IN, AUX
Playback image and sound are not synchronized.
When in D-IN source, set "D-IN MODE" to "MODE 2".
When in AUX source, set "AUX MODE" to "MODE 2".
Karaoke effect cannot be used.
When in D-IN source, set "D-IN MODE" to "MODE 1".
When in AUX source, set "AUX MODE" to "MODE 1".
(
)
Zpage 8

Hide quick links:

Publicidad

Capítulos

Tabla de contenido

Solución de problemas

loading

Tabla de contenido