Publicidad
Idiomas disponibles
Idiomas disponibles
12 • ENGLISH
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Stanley Service Center or an equally qualified
person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified
person, but not authorized by Stanley the
warranty will not be valid.
7. Labels on tool
The label on your tool may include the following
symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
.....
Use Ear
Protection
.....
V ........
Volts
n
.......
0
A ........
Amperes
Hertz
...... Class II
Construction
Watts
....
Earthing
minutes
Terminal
Alternating
....
Safety Alert
Current
Symbol
Direct
.../min..
Revolutions
Current
or Recipro-
cation per
minute
No-Load
Speed
ADDITIONAL POWER TOOL
SAFETY WARNINGS
Warning! Additional safety warnings for
grinding, sanding, wire brushing, polishing or
abrasive cutting off operations.
a. This power tool is intended to function as a grinder,
sander, wire brush, polisher or cut-off tool. Read
all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
b. Operations for which the power tool was not designed
may create a hazard and cause personal injury.
c. Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
d. The rated speed of the accessory must be at least
equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
e. The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
f.
The arbour size of wheels, flanges, backing
pads or any other accessory must properly
fit the spindle of the power tool. Accessories
with arbour holes that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
g. Do not use a damaged accessory. Before
each use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad for
cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or accessory
is dropped, inspect for damage or install an
undamaged accessory. After inspecting and
installing an accessory and run the power tool
at maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time.
h. Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear
dust mask, hearing protectors, gloves and
workshop apron capable of stopping small
abrasive or workpiece fragments. The eye
protection must be capable of stopping flying debris
generated by various operations. The dust mask
or respirator must be capable of filtering particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
Publicidad
