Publicidad
Idiomas disponibles
Idiomas disponibles
Special Cuts
Never make any cut unless the material is secured on the
table and against the fence.
Bowed material (Fig. T1, T2)
When cutting bowed material always position it as shown in
Figure T1 and never like that shown in Figure T2. Positioning
the material incorrectly will cause it to pinch the blade near
the completion of the cut.
Cutting round material
Rounded material should be clamped or held firmly to the
fence to keep it from rolling. This is extremely important when
making angle cuts.
Cutting large material (Fig. U)
Occasionally you will encounter a piece of wood a little too
large to fit beneath the lower guard.
To clear the guard over the wood, with the saw off and your right
hand on the operating handle, place your right thumb outside of
the upper portion of the guard and roll the guard up just enough
to clear the wood, as shown in Figure U. Release the guard prior
to starting the motor. The guard mechanism will function properly
during the cut. Only do this when necessary.
NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD
OPEN WHEN OPERATING THIS SAW.
Warning! Always be sure that the tool is switched off and
unplugged before adjusting or checking the tool's function.
After use
After use, wipe off chips and dust adhering to the tool with
u
a cloth or the like.
Keep the blade guard clean according to the directions in
u
the previously covered section.
Lubricate the sliding portions with machine oil to prevent rust.
u
When storing the tool, pull the carriage toward you fully.
u
Carrying the tool
Make sure the tool is unplugged.
u
Secure the blade at the 0° bevel angle and turn the base to
u
the right mitre angle fully with the slide bar locking screw (28).
Secure the slide bars after pulling the carriage toward you fully.
u
Lower the handle fully and lock it in the position by
u
pushing in the saw head locking pin (17).
Carry the tool by holding the carry handle (22).
u
If you remove the clamp, dust bag, etc., you can carry the
u
tool more easily.
Carry the tool by one hand holding the carry handle (22)
u
and one hand holding the tool base.
Caution! Always secure all moving portions before carrying
the tool.
Saw head locking pin (17) is for carrying and storage
purposes only and not for any cutting operations.
(Original instructions)
Troubleshooting
Problem
Possible Cause
Motor does
Saw not plugged in.
not start
Mitre table unlocked.
Angle of cut
inaccurate
Too much sawdust
under table.
Parts failure.
Cutting arm
Pivot spring not
cannot fully
replaced properly
raise, or
after service.
blade guard
Sawdust buildup.
cannot fully
close
Saw head locking pin
not set properly.
Saw blade damaged.
Blade binds,
Dull blade.
jams or
Improper blade.
shakes
Warped blade.
Saw blade damaged.
Saw blade loosened.
Saw vibrates
Saw not properly
or shakes
fastened down.
Workpiece not
properly supported.
Z
Protecting the environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com.
Technical data
Voltage
Speed
Blade outer diameter
Bore diameter
Weight
Blade thickness
Blade max. kerf
Mitre (max. positions)
Bevel (max. positions)
Max. cross-cut capacity at 90 °
Max mitre capacity at 45 °
Max. depth cut at 90 °
Max. depth cut at 45 °
ENGLISH
Solution
Check that all cords are plugged in.
Use mitre table locking lever (see
Adjusting the mitre angle section).
Vacuum or blow out dust. Wear eye
protection.
Contact service centre.
Contact service centre.
Clean and lubricate moving parts.
Check, adjust, and properly set saw
head locking pin.
Replace blade.
Replace or sharpen blade.
Replace blade.
Replace blade.
Replace blade.
Tighten arbor bolt.
Fasten saw to bench, stand or
table.
Properly support or clamp
workpiece.
BES700
BES710
Type 1
Type 1
V
230
230
/min
4800
5000
mm
216
254
mm
30
30
kg
12.1
14.9
mm
1.8
1.8
mm
2.8
2.8
°
+/- 47
+/- 47
°
47
47
mm
305
305
mm
203
203
mm
70
90
mm
35
40
17
Publicidad
