Publicidad
Idiomas disponibles
Idiomas disponibles
9
Operation
The cordless hand-held circular saw has overload protec-
tion, a spindle lock, a laser and an LED work light.
Please refer to the following description for the function of
the controls.
WARNING
Danger of injury!
Remove the battery from the power tool before carrying
out any work on the power tool (e.g. maintenance, tool
change, etc.) and when transporting and storing it.
There is a risk of injury if the on/off switch is operated
unintentionally.
ATTENTION
Make sure that the ambient temperature does not ex-
ceed 50°C and does not fall below -20°C during work.
ATTENTION
The product is part of the 20V IXES series and may on-
ly be operated with batteries of this series. Batteries
may only be charged with battery chargers of this se-
ries. Observe the manufacturer's instructions.
9.1
Function of the protective cover
(17) (Fig. 1)
1. Pull the retracting lever (19) of the protective cover
(17) as far as it will go.
Note:
The protective cover must not jam and must automatically
spring back to its original position when the retracting le-
ver is released.
Note:
If the function is faulty, do not operate the product and
contact our Service Centre.
9.2
Setting the cutting angle (Fig. 5)
Note:
Hold the product firmly with both hands during operation
to have better control over the product.
You can set the cutting angle with the cutting angle scale
(9).
1. Loosen the wing screw (10) for setting the cutting an-
gle.
2. Use the cutting angle scale (9) to set the required an-
gle.
3. Retighten the wing screw (10).
9.3
Setting the cutting depth (Fig. 6)
Note:
For a clean cut, select a cutting depth that is approx. 3
mm greater than the material thickness.
1. Loosen the lever (25).
2. Set the desired cutting depth on the cutting depth
scale (27).
3. Tighten the lever (25) again.
9.4
Switching the laser (7) on/off (Fig.
1)
Switching on
1. To switch the laser (7) on, push the on/off switch (5) to
position "I".
Switching off
1. To switch off, push the on/off switch (5) to position "0".
9.5
On/Off switch (2) (Fig. 1)
ATTENTION
Before use, check the inserted tool to ensure all fasten-
ing parts are attached correctly.
Switching on
1. Press the switch-on interlock (3) on the handle (1) to
the right or left.
2. To switch on the product, push the on/off switch (2).
Note:
After the product has started, you can release the switch-
on interlock again.
Switching off
1. To switch off, release the on/off switch (2).
If the switch-on interlock (3) is in the centre position,
the product is secured from being switched on.
9.5.1
This product is equipped with an LED work lamp to illumi-
nate the immediate work area and improve visibility in
poorly lit environments.
CAUTION
Do not look directly into the LED work lamp or the light
source.
1. The LED work lamp (8) lights up automatically as
soon as the product is switched on.
9.6
Overload switch-off
In the event of overloading, the motor will switch itself off.
After a cool-down period (time varies) the motor can be
switched back on again.
9.7
Right-angled sawing (Fig. 1)
1. Hold the product firmly with both hands, one hand on
the handle (1) and the other on the additional grip (4).
2. Switch off the product, as described in 9.5.
3. Place the product down with the front part of the base
plate (18) on the workpiece.
4. Saw forwards with moderate pressure – never back-
wards.
9.8
Mitre cuts up to 45° (Fig. 1)
1. Set the desired cutting angle as described under 9.2.
2. Hold the product firmly with both hands, one hand on
the handle (1) and the other on the additional grip (4).
3. Switch off the product, as described in 9.5.
4. Place the product down with the front part of the base
plate (18) on the workpiece.
www.scheppach.com
LED work lamp (8) (Fig. 1)
GB | 27
Publicidad
