Publicidad
Idiomas disponibles
Idiomas disponibles
1.0
Introduction
This manual provides safety and installation instructions
for IEC certified Maxeon photovoltaic modules carrying
the TUV logo on the product label (Figure 1).
Figure 1
Important!
Please read this instruction sheet in its
entirety before installing, wiring, or using this
product in any way. Failure to comply with these
instructions will invalidate the Maxeon Limited
Warranty for PV Modules.
1.1 Disclaimer of Liability
The installation techniques, handling and use of this
product are beyond company control. Therefore, Maxeon
does not assume responsibility for loss, damage or
expense resulting from improper installation, handling or
use.
1.2
Conformity
to
International
Commission (IEC) standards
This product meets or exceeds the requirements set forth
by IEC 61215 Edition 3-2016 for PV Modules, as well as IEC
61730 Edition 1 and 2 series for Class II applications. The
IEC Standard covers flat-plate PV modules intended for
installation on buildings and those intended to be
freestanding. This product is not intended for use where
artificially concentrated sunlight is applied to the module.
This manual shall be used in combination with industry
recognized best practices. Modules should be installed by
certified professionals only.
1.3 Limited Warranty
Module limited warranties are described in the Maxeon
warranty
document
www.sunpower.maxeon.com. Please read this document
for more information.
Warranties do not apply to any of the following;
PV Modules subjected to: (i) misuse, abuse, neglect or
accident; (ii) alteration or improper installation
(improper installation includes, without limitation,
installation or array that does not comply with all
Maxeon installation instructions and operations and
maintenance instructions of any type (as may be
amended and updated from time to time at Maxeon's
sole discretion), and all national, state, and local laws,
codes, ordinances, and regulations); (iii) repair or
modification by someone other than an approved
service
technician
exceeding the voltage, wind, snow load specifications;
and any other operational specification; (v) power
failure surges, lightning, flood, or fire; (vi) damage
from
persons,
biological
chemical exposure; (vii) glass breakage from impact
or other events outside Maxeon's control.
©2024 Maxeon Solar Technologies, Ltd. All rights reserved. Specifications included in this manual are subject to change without notice.
Electrotechnical
obtainable
of
Maxeon;
(iv)
conditions
activity,
or
industrial
Safety and Installation Instructions - Document 001-15497 Rev.AB
2.0
Safety Precautions
Before installing this device, read all safety instructions in
this manual.
Danger!
Module interconnects pass direct current (DC)
and are sources of voltage when the module is under
load and when it is exposed to light.
arc across gaps and may cause injury or death if
improper connection or disconnection is made, or if
contact is made with module components that are
damaged.
Do not connect or disconnect modules
when current from the modules or an external source
is present.
• Cover all modules in the PV array with an opaque cloth
or material before making or breaking electrical
connections.
• Do not disconnect any modules when its inverter is
feeding in to the grid. Switch off the inverter before
disconnecting, reinstalling or making any action with
the modules.
• For connectors, which are accessible to untrained
people, it is imperative to use the locking connectors
and safety clips, if applicable, in order to defend
against untrained personnel disconnecting the modules
once they have been installed.
• All installations must be performed in compliance with
all applicable regional and local codes.
• There are no user serviceable parts within the module.
Do not attempt to repair any part of the module.
• Installation should be performed only by qualified
personnel.
• Remove all metallic jewelry prior to installing this
product to reduce the chance of accidental exposure to
live circuits.
• Use insulated tools to reduce your risk of electric shock.
• Do not stand on, walk, drop, and scratch or allow objects
to fall on the glass surface of the modules.
• Damaged modules (broken glass, torn back sheet,
broken j-boxes, broken connectors, etc) can be
electrical hazards as well as laceration hazards. Contact
at
with damaged module surfaces or module frame can
cause electric shock. Damaged modules should be
immediately disconnected from the electric system. The
module should be removed from array as soon as
possible
and
instructions.
• Unconnected connectors must always be protected
from pollution (e.g dust, humidity, foreign particles,
etc), prior to installation. Do not leave unconnected
(unprotected) connectors exposed to the environment.
A clean assembly environment is therefore essential to
avoid performance degradation.
• Do not allow the connectors to come in contact with
chemicals such as sunscreen, greases, oils and organic
solvents which may cause stress cracking.
• Do not install or handle the modules when they are wet
or during periods of high wind.
• Do not block drain holes or allow water to pool in or near
module frames
• Contact your module supplier if maintenance is
necessary.
• Save these instructions!
MAXEON SOLAR TECHNOLOGIES, LTD.
Direct current can
contact
the
supplier
EN
for
disposal
Publicidad
