Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
GB
INITIAL START-UP
APPLICATIONS:
Make sure that no loops occur when
The 16.87 shredder/baler combination is
feeding strip material. Danger of
a large-scale shredding system for the shredding
injury!
and baling of large volumes of paper.
The system shreds cardboard and crumpled
MAINS CONNECTION:
paper just as easily as it does flat paper.
a) Loop resistance within the mains power supply
The shredder may only be used for
system at the installation site may not exceed
shredding paper and cardboard!
0.5 ohm.
The shredding of other data media may
b) The conductor cross-section of the power cable
result in bodily injury (e.g. due to splinter -
at the installation site must be laid out such that
ing of hard materials etc.), or damage
voltage does not drop more than 15% if the
to the machine (e.g. destruction of the
machine jams (the machine's blocking current
cutting system etc.).
is equal to 6 times nominal current).
SHREDDER OPERATION
USING THE SHREDDER (Fig. 6):
Attention: The system only functions if:
Proceed as follows to switch the shredder on:
a) The emergency stop bar (14) is released (pull
1. Insert the enclosed key into the key switch (2)
red bar at table forward)
and turn clockwise.
b) The key switch (2) has been unlocked (turn
2. Operate the mains switch (1) to position „1".
key clockwise)
After a delay of 2 seconds, the „ready" (7) and
c) The mains switch (1) has been switched on
„ram at rear" (11) indicator lights come on.
(switch position "1")
3.
O
p
e
a r
e t
h t
e
c „
t u
e t
f r
r o
w
a
d r
" s
p
s u
h
b
t u
o t
n
3 (
. )
e) The safety switch activator (19) (fig. 3) has
The cutter and conveyor belt start.
been inserted into the safety switch at the
The light of the „cutter forwards" display (6)
baler
comes on.
f) The inlet flap (30), the discharge flap (31) and
Note : If, when the shredder is started, the
the cover flap (27) are closed.
baling ram (32) of the baler is not in its basic
position (rearmost position), a compression
FEEDING MATERIAL TO THE SHREDDER:
stroke with following return stroke is carried out
The operator may not stand at a level
automatically before the cutter and conveyor
higher than that of the machine when
belt start.
feeding material to the shredder!
Elevated surfaces in front of the machine
(e.g. with pallets, crates etc.) are
ited as regards required safety distance
from the cutting system.
FEEDING STACKED PAPER:
Stacks of up to 550 sheets
pending upon type of paper) can be placed onto
the running conveyor belt for transport to the
cutting system, as well as crumpled paper and
cardboard.
In order to prevent sudden overloading of the
cutting system it is advisable to feed flat paper
35
44
27
18
diagonally, i.e. corner first.
Never feed more than the maximum
indicated quantity of paper to the
shredder (see "TECHNICAL DATA")!
If too much paper nevertheless enters
the cutting system at once, refer to
"AUTOMATIC SWITCHING FOR OVER
LOADED SHREDDER".
FEEDING WITH COMPLETE BINDERS!
Shredders equipped with a cutting system with 7.8
x 55 mm or 11.8 x 55 mm cutting width, can also
be fed with complete binders (incl. metal parts).
In this case the binder should be opened and the
contents spread out equally.
Important note: The removing of the metal parts
beforehand makes the recycling of the shredded
material possible and ensures a longer life of the
cutting system.
31
36
30
fig. 2
16.87
CHECKING THE DIRECTION OF ROTATION:
1. Release the emergency stop bar (14) (fig. 7) at
the shredder table (pull forward) and turn the
mains switch on (1) (switch position "1").
2. Unlock the key switch (2) (fig. 6) and operate
the „cutter forwards" pushbutton (3).
3. Check the direction of rotation of the shred -
der and reverse the poles at the mains plug if
necessary.
The phases at the mains plug may
only be reversed by properly trained
personnel.
After all installation and connection work has
been properly completed, the machine may be
placed into service.
AUTOMATIC SWITCHING
FOR OVERLOADED SHREDDER:
If the shredder should be „overfed", the unit rectifies
the problem automatically, as follows:
1. The cutter jams.
2. Cutter and conveyor belt move backwards a
short distance. The material being shredded is
released.
3. The cutter and conveyor belt switch to forward
operation. The material to be shredded is once
again fed to the cutter.
This procedure is repeated automatically until
all the material has been fed through and shred
ded.
JAM OUTLET:
If the space in the hopper (44) (fig. 2) is completely
filled with cutting material due to a jam in the filler
prohib-
hole of the baler, the machine switches off when
the cover flap (27) is raised (fig. 2). The display
(9) "Jam outlet" flashes .
If this is the case, switch the machine off at the
main switch (1), lift up the cover flap (27) and
of flat paper (de -
remove the material from the machine by hand.
Then you can switch the machine on again and
continue shredding.
Note: the machine can only be started when the
cover flap (27) is closed.
3
4
-
5
2
1
fig. 6
12
SCHALTBILD / WIRING DIAGRAM / PLAN DE MONTAGE / DIAGRAMA ELÉCTRICO
ESQUEMA ELECTRICO / SCHEMA ELETTRICO / SCHÉMA ZAPOJENÍ
-
6
7
8
9
10
11
12
13
16.87
61
Publicidad
Tabla de contenido
