Ego Power+ SNT2120E-AP Manual página 11

BATTERY HIGH-TEMPERATURE PROTECTION
If the battery temperature exceeds 70°C during operation,
the temperature- protection circuit will immediately shut
off the snow blower to protect the battery packs from
overheating damage. The power indicator on the snow
blower will be off and the LED indicator on the battery
pack will flash orange or shine red. Please refer to the
"BATTERY PROTECTION" section in battery operator's
manual for more about the LED indicator on the battery
pack.
Release the bail switch and wait until the overheated
battery pack(s) cool down and the light on the battery LED
indicator turns green, then restart the snow blower.
To prevent shut off due to battery high-temperature
protection, don't try to use a single battery to power
the snow blower when the depth of the accumulated
snow exceeds 76 mm or when the snow is very wet or
icy. We recommend the use of two batteries working
simultaneously. This is helpful in attaining the peak power
of the snow blower.
After high-temperature protection has occurred, slow down
your pace and narrow the width of the snow-clearing swath
to reduce the load on the battery.
MAINTENANCE
WARNING:
Make sure to turn off the unit and remove
the battery pack(s) before performing any maintenance task
on your snow blower.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
LUBRICATING THE MACHINE
All of the bearings in this product are lubricated with an
amount of high grade lubricant sufficient for the life of
the unit under normal operating conditions. Therefore, no
further bearing lubrication is required.
REPLACING THE SCRAPER BAR
Required tools (not included):
◾
8 mm open-end wrench
◾
T20 Torx screwdriver
1. The scraper bar is located at the bottom of the snow
blower deck, beneath the auger (Fig. F1).
F1-1 Scraper bar
56-VOLT LITHIUM-ION CORDLESS SNOW BLOWER — SNT2120E-AP
2. Turn the snow blower on its side (Fig. F2).
3. Wear gloves. Remove the 5 sets of nuts, spring
washers, and bolts from the outside and remove the 2
Torx screws from the inside. Detach the worn scraper
bar (Fig. F2).
F2-1 Outside nut (x5) F2-2 Torx screw (x2)
4. Attach the new scraper bar and insert the 2 Torx
screws (Fig. F3).
F3-1 Inside hole (x2) F3-2
F3-3 Torx screw (x2)
5. Insert the 5 bolts and tighten with spring washers and
nuts (Fig. F4 & F5).
F5-1 Nut F5-2 Spring washer
F5-3 Deck F5-4 Scraper bar
F5-5 Bolt
REPLACING THE RUBBER PADDLES & RUBBER AUGERS
To replace the rubber paddles: (Fig. G1)
G1-1 Rubber paddles G1-2
Required tools (not included):
◾
Flat head screwdriver
◾
10 mm open-end wrench
1. Wear gloves. Manually rotate the steel auger to
the appropriate position for easy rubber paddle
disassembly.
2. Remove all securing bolts and nuts to take the rubber
paddles out.
3. Replace them with the new rubber paddles, and
securely tighten them.
To replace the rubber augers (Fig. G2)
G2-1 Rubber auger (x4) G2-2
2 sets of bolts and nuts on each auger (total of
G2-3
8 sets)
EN
Scraper bar (shiny
surface facing inside)
2 sets of bolts and
nuts on each paddle
(total of 4 sets)
1 set of bolt, washer
and nut on each
auger (total of 4 sets)
11