Publicidad
Idiomas disponibles
Idiomas disponibles
en
ENGLISH
3. If the current is too high (for example, if the
machine seizes continuously for long periods),
the machine switches off.
Switch off the machine at the trigger switch (18).
Then continue working as normal (in this case,
read in particular the safety instructions in
Chapter 4.2 kickback...). Try to prevent the
machine from seizing.
4. In the event of kickback, the machine is
switched off. There will be a warning signal (3 x
beeps and 3 x flashes of the electronic signal
indicator (20).
Switch off the machine at the trigger switch (18)
and let the saw blade come to a standstill.
Centre the saw blade in the saw gap and check
that the saw teeth are not caught in the
workpiece. Then continue working as normal (in
this case, read in particular the safety
instructions in Chapter 4.2 kickback...).
7.2
Switching on and off
When the locking button (17) is pushed
forwards, the motor section can be moved
downwards. The saw blade then emerges from the
guard. Caution, risk of injury.
Switching on: Push the locking button (17)
forwards and hold, then actuate the trigger (18).
Switching off: Release the trigger switch (18).
7.3
Working Directions
Do not switch the machine on or off while the
saw blade is touching the workpiece.
Let the saw blade reach its full speed before
making a cut.
When sawing, never remove the machine
from the material with the saw blade turning.
Allow the saw blade to come to a standstill.
If the saw blade blocks, turn the machine off
immediately.
Do not set the machine down until the saw
blade has come to a standstill.
Plunge cuts: The motor section is in the upper
position, the saw blade does not project from the
guide plate. Hold the machine tightly with both
hands and place with the guide plate onto the
workpiece. Switch on the machine. Lower the motor
section slowly to the set cutting depth and then
move slowly in cutting direction.
Sawing along a straight line: the cutting indicator
is used here (2). The left edge (marked red)
indicates the direction of the cut if the saw blade is
held vertically. The right edge indicates the
direction of the cut if the saw blade is held at 45°.
Sawing along a rail secured on the workpiece:
In order to achieve an exact cutting edge, you can
attach a rail to the workpiece and then guide the
hand-held circular saw by means of the guide plate
along this rail.
Sawing with a rip fence (see Accessories
chapter):
For cuts parallel to a straight edge. The rip fence
can be inserted from either side into the support
18
provided for it. The cut width can be read off at the
mark (8). Fix using both clamping levers (1). It is
best to calculate the exact cut width by making a
test cut.
Sawing with a guide rail (see Accessories
chapter):
For dead straight, tear-free cutting edges with
millimetre precision. The anti-slip coating keeps the
surface safe and protects the workpiece against
scratches. See Accessories section. The rotary
button (15) is used for setting a clearance-free fit.
Only for cordless machines:
Battery pack heat generation:
Under extremely hard application conditions
(e.g. sawing thick wooden planks), the heavy load
can cause the battery pack to heat (> 60 °C). To
conserve the battery pack, allow it to cool down
before continuing work.
8. Maintenance
8.1
Changing saw blades
The saw blade must be stationary.
Remove the battery pack from the machine /
pull the mains plug from the socket.
Risk of injury, even with the blade at standstill.
Wear protective gloves.
See figure page 3.
1. Press the locking button (13) and move.
2. Move in such a way that the read-off edge (10) is
pointed to the symbol "saw blade changing".
13 10
3. Release the locking button (13) again.
4. Turn the lever (14) clockwise up to the stop.
5. Push the locking button (17) forwards and lower
the motor section a little. Release the locking
button (17) again.
6. Push the motor section down until it locks in
place at the stop.
Changing
Turn the saw spindle slowly with the spanner (25) in
the saw blade fixing screw (31) until the lock
catches.
Unscrew the saw blade fixing screw in anti-
clockwise direction and remove the outer saw blade
flange (32). Remove the saw blade.
Ensure that the inner saw blade flange (34) is
inserted in the right way: The inner saw blade
flange (34) has 2 sides, diameter 20 mm and 5/8"
(16 mm). Ensure a precise fit of saw blade mounting
hole to the inner saw blade flange (34)! Incorrectly
installed saw blades do not run smoothly and lead
to loss of control.
Insert a new saw blade. Make sure the direction of
rotation is correct. The direction of rotation is
Publicidad
