Publicidad
Idiomas disponibles
Idiomas disponibles
TEMPERATURE ADJUSTMENT BUTTONS:Pressing
the
or
button, the display starts to flash showing
the set temperature for 3 seconds, after that it will show
again to the real water temperature. When it is flashing you
can adjust the temperature using the
The default temperature is 35°C (95°F).
Temperature adjustment ranges from 20°C (68°F) to
40°C (104°F).
ON/OFF BUTTON:After activating the GFCI, press and
hold the
button for 2 seconds. The
to green and the control panel is activated. Press and
hold
button for 2 seconds to turn off all currently
activated functions.
The WATER HEATER rate may change in the conditions below:
• When the outdoor temperature is below 15°C (59°F).
• If the cover is not in position. Always keep the spa cover on when the spa is not in use; it avoids dust contaminating the water and it minimizes heat loss.
• The water temperature shown on the display may not be correct, if the filtration system is not activated. To read the correct water temperature on the
display, run the filtration system for at least a minute.
• The water temperature as tested by an external thermometer may vary from the temperature as displayed on the spa panel by as much as
approximately 2°C (35.6°F).
WINTER USE INSTRUCTIONS
It is important to follow these suggestions if you are setting up the spa during the winter period. This will prevent any damage to the spa
heater and material of the liner, extending the life of your product drastically.
• If the outdoor temperature is below 10°C (50°F), to avoid any damage to spa liner, keep the package indoors where the temperature is above
15°C (59°F). This will make the spa liner more flexible and easier to set up.
• Open the package and inflate the spa liner using the spa heater in a room where the temperature is above 15°C (59°F).
• Position the spa liner outdoors in the desired position, then connect the spa heater and fill with water. The water temperature used to fill the spa must be
above 6°C (42.8°F), otherwise when you begin to operate with the spa heater, the E03 alarm will appear.
• You can keep the spa on during winter when the temperature is lower than 6°C (42.8°F). The Freeze Shield™ system automatically keeps the water
temperature between 6°C (42.8°F) and 10°C (50°F), and it will prevent the water from freezing.
• If the water temperature is below 6°C (42.8°F), the spa heater must always be on. In this mode, the Freeze Shield™ system can keep the internal
temperature between 6°C (42.8°F) and 10°C (50°F) to prevent damage, such as water freezing in the pipes or the circulation system.
• If any alarms appear on the display, the Freeze Shield™ system isn't working. Be sure to check the status of your spa if the outdoor temperature is
below 6°C (42.8°F). In case of a long-term absence from home when there is a risk of temperatures falling below 6°C (42.8°F), we strongly suggest
disassembling the spa and storing it following the storage procedure.
• Any damage as a result of using the spa in these conditions is the responsibility of the customer. Do not use the spa when the ambient temperature
reaches -10°C (14°F).
HEATING TIME
• To reach 40°C (104°F), the heating duration required is based on the starting water temperature and ambient temperature, the data below is purely for
reference. To display the current water temperature, run the filter system for at least a minute.
Ambient Temperature
10ºC (50ºF)
15ºC (59ºF)
20ºC (68ºF)
25ºC (77ºF)
30ºC (86ºF)
• We do not recommend setting up the spa, filling it and heating it for the first time when the outdoor ambient temperature is below 10ºC (50ºF) as it will
take a very long time to heat.
• To reach and maintain maximum water temperature of 40ºC (104ºF), outdoor temperature must not be lower than -5ºC (23ºF).
• Do not operate the spa below -10ºC (14ºF).
• Be sure to cover the spa with the spa cover whenever the heating function is activated. Leaving the spa uncovered will increase
the heating duration required. When the spa is assembled with water, do not switch off the spa heater if the temperature
is lower than 6ºC (42.8°F).
SPA HEATER SPECIFICATION
Power Rate
110-120V AC, 60Hz,
Single Phase 12A at 20ºC (68ºF)
or
button.
button turns
Water Temperature
10ºC (50ºF)
15ºC (59ºF)
20ºC (68ºF)
25ºC (77ºF)
30ºC (86ºF)
Massage Tube Blower
6.5A
14
CELSIUS/FAHRENHEIT TOGGLE:The temperature
can be displayed in either Fahrenheit or Celsius.
WATER FILTER BUTTON:The
pump on and off. The
activated.
FOR SPA EQUIPPED WITH Wi-Fi ONLY
Wi-Fi ACTIVATION:For the Wi-Fi operation instruction,
read the spa Wi-Fi instruction leaflet included in the
package.
Set Temperature
40ºC (104ºF)
40ºC (104ºF)
40ºC (104ºF)
40ºC (104ºF)
40ºC (104ºF)
Heat Element
11.3A at 20ºC (68ºF)
button turns the filter
button turns to red when
Heating Duration
23-40hr
18-36hr
13-29hr
9-20hr
7-15hr
Water Pump
0.7A
Publicidad
