Publicidad
Idiomas disponibles
Idiomas disponibles
Adjusting the tilt of the squeegee body:
4.
Loosen the retainer knob (3) of the squeegee tilt adjustment knob (4) (Fig.3).
5.
To adjust the tilt of the squeegee body rubber blades in relation to the floor, tighten or loosen the
knob (5) (Fig.4) until the blades are bent outwards by about 30° in relation to the floor, in an even
manner along their entire length.
NB: make sure the adjustment is correct by looking at the instrument (6) on the squeegee body
(Fig.5).
6.
Once the adjustment has been completed, tighten the retainer knob (3).
3
4
3
Fimap is committed to creating its products by respecting the environment,
investing in the development of sustainable solutions and technologies, seeking
materials that can easily be recycled, and ensuring that the entire production
process has a low environmental impact.
At the end of the machine's life cycle, FIMAP offers the RECYCLING MANUAL
which can be downloaded from the link
https://www.fimap.com/it/fimap/sostenibilita/75/riciclabilita.html
in order to provide some simple information on how to dispose of the materials that
make up your scrubbing machine.
Before proceeding with disposal, it is essential to contact your nearest authorised collection centres
directly, in accordance with the legislation in force in the country where the machine is used.
CHOOSING AND USING THE BRUSHES
POLYPROPYLENE BRUSH (PPL)
Used on all types of floors. Good resistance to wear and tear, and hot water (no greater than 50°C.).
The polypropylene is non-hygroscopic and therefore retains its characteristics even when working in
wet conditions.
ABRASIVE BRUSH
The bristles of this type of brush are charged with highly aggressive abrasives. It is used to clean very
dirty floors. To avoid floor damage, work only with the pressure strictly necessary.
BRISTLE THICKNESS
Thicker bristles are more rigid and are therefore used on smooth floors or floors with small joints.
On uneven floors or those with deep joints, it is advisable to use softer bristles which can enter the
gaps more easily.
Remember that when the bristles are worn and therefore too short, they will become rigid and are no
longer able to penetrate and clean deep down. In this case, like with over-large bristles, the brush
tends to jump.
PAD HOLDER
The pad holder is recommended for cleaning shiny surfaces.
There are two types of pad holder:
1. The traditional pad holder is fitted with a series of anchor points that allow the abrasive floor pad to
be held and dragged while working.
2. The CENTRE LOCK type pad holder not only has anchor points, but also a snap-type central
locking system in plastic that allows the abrasive floor pad to be perfectly centred and held without
any risk of it becoming detached. This type of pad holder is recommended above all for machines
with more than one brush, where the centring of the abrasive discs is difficult.
MACHINE
CODE
434538
434539
MAXIMA 2017
434540
55 BT
459951
405527
442823
442824
MAXIMA 2017
442825
60 BT
442826
442828
442005
442661
MAXIMA 2017
442662
50 BTO
443711
443712
10077109-AB_UM_Maxima 2017 BT-BTO-BTS.indb 38
10077109-AB_UM_Maxima 2017 BT-BTO-BTS.indb 38
5
4
4
5
DISPOSAL
QTY
BRISTLE
NOTES
1
PPL 0.3
BLUE BRUSH
1
PPL 0.6
WHITE BRUSH
1
PPL 0.9
BLACK BRUSH
1
ABRASIVE
BRUSH
1
PAD HOLDER WITH CENTRE LOCK
2
PPL 0.3
BLUE BRUSH
2
PPL 0.6
WHITE BRUSH
2
PPL 0.9
BLACK BRUSH
2
ABRASIVE
BRUSH
2
PAD HOLDER WITH CENTRE LOCK
ABRASIVE PAD 508X355
1
(COLOUR: RED)
ABRASIVE PAD 508X355
1
(COLOUR: GREEN)
ABRASIVE PAD 508X355
1
(COLOUR: BLACK)
ABRASIVE PAD 508X355
1
(COLOUR: WHITE)
ABRASIVE PAD 508X355
1
(COLOUR: BROWN)
MACHINE
CODE
QTY
445594
445595
MAXIMA 2017
50 BTS
445596
445597
EC DECLARATION OF CONFORMITY
37059 Santa Maria di Zevio (VR)
declares under its sole responsibility that the products
FLOOR SCRUBBING MACHINES
mod. Maxima 2017 55 BT CB - Maxima 2017 60 BT CB - Maxima 2017 50 BTO CB
Maxima 2017 50 BTS CB
comply with the provisions of Directives:
•
2006/42/EC: Machinery Directive.
•
2014/35/EC: Low Voltage Directive.
•
2014/30/EC: Electromagnetic compatibility directive.
The person authorized to compile the technical file:
Mr. Giancarlo Ruffo
Via Invalidi del Lavoro, 1
37059 Santa Maria di Zevio (VR) - ITALY
Santa Maria di Zevio (VR), 01/01/2018
37059 Santa Maria di Zevio (VR)
declares under its sole responsibility that the products
FLOOR SCRUBBING MACHINES
mod. Maxima 2017 55 BT - Maxima 2017 60 BT - Maxima 2017 50 BTO - Maxima 2017 50 BTS
comply with the provisions of Directives:
•
2006/42/EC: Machinery Directive.
•
2014/30/EC: Electromagnetic compatibility directive.
The person authorized to compile the technical file:
Mr. Giancarlo Ruffo
Via Invalidi del Lavoro, 1
37059 Santa Maria di Zevio (VR) - ITALY
Santa Maria di Zevio (VR), 01/01/2018
UKCA DECLARATION OF CONFORMITY
37059 Santa Maria di Zevio (VR)
declares under its sole responsibility that the products
FLOOR SCRUBBING MACHINES
mod. Maxima 2017 55 BT CB - Maxima 2017 60 BT CB - Maxima 2017 50 BTO CB
Maxima 2017 50 BTS CB
comply with the provisions of Directives:
•
S.I. 2008/1597 Supply of Machinery (Safety) Regulations 2008 (as amended).
•
S.I. 2016:1101 Electrical Equipment (Safety) Regulations 2016 (as amended).
•
S.I. 2016:1091 Electromagnetic Compatibility Regulations 2016 (as amended).
The person authorized to compile the technical file:
Mr. Giancarlo Ruffo
Via Invalidi del Lavoro, 1
37059 Santa Maria di Zevio (VR) - ITALY
Santa Maria di Zevio (VR), 01/01/2018
ENG - 38
BRISTLE
NOTES
2
PPL 0.3
BLUE BRUSH
2
PPL 0.6
WHITE BRUSH
2
PPL 0.9
YELLOW BRUSH
2
ABRASIVE
BRUSH
The undersigned manufacturer:
FIMAP spa
Via Invalidi del Lavoro, 1
Legal representative
The undersigned manufacturer:
FIMAP spa
Via Invalidi del Lavoro, 1
Legal representative
The undersigned manufacturer:
FIMAP spa
Via Invalidi del Lavoro, 1
Legal representative
T
Fimap S.p.A.
Giancarlo Ruffo
Fimap S.p.A.
Giancarlo Ruffo
Fimap S.p.A.
Giancarlo Ruffo
02/02/2024 10:27:35
02/02/2024 10:27:35
Publicidad
