Publicidad
GENERAL INSTRUCTIONS.-
Read the instructions in this manual. This gives important
information on the safety, use and maintenance of the
machine.
Follow the following recommendations:
1
Keep children and animals away from the machine. Do
not leave children unsupervised around the equipment.
2
The machine will only be used by 1 person at the same
time.
3
Work at the recommended exercise level, do not get to
exhaustion. If you feel pain or discomfort of any kind, stop
exercising immediately and consult your doctor.
4
Use the appliance on a solid, level surface with 1 meter
around. It is not advisable to keep your unit in wet place
because the oxidation would be inevitable. Do not use the
equipment outdoors.
5
Keep hands and feet away from moving parts.
6
Use suitable clothing and footwear. Tighten the laces
properly.
7
Use the equipment according to the functions described
in the manual, do not use accessories or exercises other
than those described by the manufacturer.
8
Do not place any sharp objects around the machine.
9
Do not allow children or disabled persons use the
appliance without the strict supervision of a qualified
person.
10
Do stretches before using the computer as a warmup.
11
Select an appropriate weight to their physical condition.
12
Do not use the equipment if it is damaged or
incomplete.
13
It is recommended to exercise a monitor to oversee the
exercise.
14
This unit has been designed for home use. The
maximum user weight is 150 kg.
Caution: Consult your doctor before beginning to use
the machine. This advice is especially important for
those over 35 or suffering from health problems.
Keep these instructions safe for future use.
MAINTENANCE.-
1 Lubricate moving parts regularly. At least once a year.
2 Check that all parts are tight and that the machine is
working properly before first use.
3 Use a damp cloth to clean the equipment. The use of
solvents is not recommended.
English
ASSEMBLY INSTRUCTIONS.-
Saque la unidad de la caja y compruebe que tiene todas
las piezas, Fig.A, Fig.B.
Para el montaje de esta máquina, se recomienda la
ayuda de una segunda persona.
1.- Attach the vertical tube (5) to the lower frame (1) and fit
the screw (17) together with the washer (20), Fig.1. Follow
the same process for the other side.
Attach the upper connecting tube (3) and fix it to the
vertical tubes by placing the fixing plates (15) and using
the screws (18) and the washers (20), Fig.1.
Then attach the lower connecting tube (12) and fix it by
placing the fixing plates (14) and using the screws (18)
together with the washers (20), Fig.1.
NOTE: Do not fully tighten the screws.
2.- Attach the front vertical tube (5) to the lower frame (1) and
fit the screw (17) together with the washer (20), Fig.2. Follow
the same process for the other side.
Place the plates (14), the screws (18), the washers (20) and
the nuts (19), Fig.2.
Position the upper tube (2) between the front and rear upright
tubes and fit the screws (18), the washers (20) and the nuts
(19), Fig.2. Follow the same process for the other side.
Position the upper bar (13) between the front vertical tubes
and fix it by placing the fixing plates (15) and using the
screws (18), washers (20) and nuts (19), Fig.2.
Fully tighten all the screws from the first and second
step.
3.- Attach the supports (4) on the lower tubes and fix them by
placing the fixing plates (16) and using the screws (18) and
washers (20), Fig.3.
Attach the supports (9), (7) and (11) on the left front upright
tube and the supports (8), (6) and (10) on the right upright
tube, Fig.3.
4.- Remove the plugs (A) from the lower frame, Fig.4.
Position the lower tubes (4) and fix them to the lower frame
using the screws (26), the washers (33) and the nuts (31),
Fig.4.
Attach the pulley (2) and the connecting tube (3) to the
lower frame and fit the screws (26), the washers (33) and
the nuts (31), Fig.4.
Attach the rear connecting tube (5) and fix it to the lower
tubes (4) and (3) by placing the fixing plates (17) and using
the screws (26), (29), the washers (33) and the nuts ( 31),
Fig.4.
5.- Place the bar (13) and the supports (15) on the top
weight (12) using the screws (28), (22), the washers (33)
and the nuts (31), (30), Fig.5.
Place the top weight assembly on the bars (8). Place the
bushings (14) and the cushions (21) on the bars (8) and
insert the bars (8) into the lower tube (3), Fig.5.
Insert the screws (24) to prevent the bars (8) from coming
off.
Remove the plugs (B) from the upper tube.
Place the upper pulley frame (1) on the upper ends of the
bars (8) and fix it to the upper tube by placing the fixing
plate (17) and using the screws (26), the washers (33) and
the nuts (31), Fig.5.
15
Publicidad
