Publicidad
Idiomas disponibles
Idiomas disponibles
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. A)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool
1. Align the battery pack
14
Figure A.
2. Slide it in until the battery pack is firmly seated in the tool
and ensure that you hear it snap into place.
To Remove the Battery Pack from the Tool
15
1. Press the release button
pack out.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. A)
Some D
WALT battery packs include a fuel gauge which consists
e
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
20
button
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Bevel Adjustment (Fig. A)
The bevel angle can be adjusted between 0° and 47°.
1. Loosen the bevel adjustment knobs
2. Set the bevel angle by tilting the saw shoe
indicates the desired angle on the bevel scale
3. Tighten the bevel adjustment knobs
Changing the Saw Blade (Fig. A–C)
nOTE: It is not necessary to remove the outer blade cover
to change the blade.
1. Remove the battery pack.
2. Press the spindle lock button
WALT battery packs and chargers.
e
14
is fully charged.
with the rails as shown in
and firmly pull the battery
7
.
4
until the mark
6
.
7
.
23
12
.
3. Press the plunge saw down until it stops (blade
change position).
4. Turn the spindle lock lever
5. Hold the spindle lock lever
wrench found in the front handle
the lock position is found.
nOTE: The blade
10
is now locked and cannot be turned
by hand.
6. Use the hex wrench to turn the blade clamping screw
counterclockwise to remove.
25
7. Remove the outer flange
new blade on the inner flange
25
8. Replace the outer flange
Turn the screw clockwise by hand.
nOTE: The direction of rotation of the saw blade and the
rotation of the plunge saw MUST be the same.
9. Tighten the blade clamping screw firmly using the
hex wrench.
10. Release and turn the spindle lock lever
until it stops.
11. Move the plunge saw back to top position.
1
12. Push the plunge trigger
blade change mode.
Adjusting the Riving Knife (Fig. A–C)
For the correct adjustment of the riving knife
Figure C. Adjust the clearance of the riving knife after changing
the saw blade or whenever necessary.
1. Follow Changing the Saw Blade steps 1–5.
2. Loosen the riving knife adjustment screw
wrench and set the riving knife as shown in Figure C.
3. Tighten the riving knife adjustment screw
4. Turn the spindle lock lever
it stops.
5. Move the plunge saw back to top position.
1
6. Push the plunge trigger
blade change mode.
Depth of Cut Adjustment (Fig. D)
The cutting depth can be set at 0–59 mm without guide rail
attached; with the guide rail attached: 0–55 mm.
1. Loosen the depth adjustment knob
pointer to obtain the correct depth of cut.
2. Tighten the depth adjustment knob
nOTE: For optimal results, allow the saw blade to protrude from
the workpiece by about 3 mm (Fig. D).
If this logo appears on your tool, your tool is
equipped with Wireless Tool Control.
Wireless Tool Control (Fig. A)
(Available on some units)
CAUTION: Read all safety warnings, instruction and
specifications of the appliance which is paired with
this tool.
EnGLIsh
13
clockwise until it stops.
13
down and using the hex
11
, rotate the blade until
24
10
and used blade
. Place the
26
.
24
and blade clamping screw
13
counterclockwise
forward, to take the saw out of
21
, refer to
22
with a hex
22
.
13
counterclockwise until
forward, to take the saw out of
8
and move the
8
.
.
39
Publicidad
