EINHELL TC-PL 750 Manual De Instrucciones Original página 30

6. Operation
6.1 ON/OFF switch (Fig. 5)
•
The hand-held electric plane comes with a
safety switch which is designed to prevent
accidents.
•
To switch on the tool, press the side safety
lock-off (3) and press the button switch(4).
•
Release the button switch (4) to switch off the
electric plane. The button switch (4) jumps
back into its starting position.
6.2 Practical tips
Warning! Only ever bring the hand-held electric
plane towards the workpiece while switched on.
6.2.1 Planing surfaces
Now adjust the desired chip depth. Equip the front
base plate and place the hand-held electric plane
onto the piece of wood you whish to plane. Then
switch on the plane. Push to electric plane over
the surface with both hands and make sure that
the both the front and the rear base plate lie fl at
on the workpiece.
Used a low chip depth for fi nishing surfaces and
complete several passes over the surface.
6.2.2 Chamfering edges (Fig. 6-7)
•
There are three V-shaped grooves (a) in the
front base plate that enable you to plane
edges at an angle of 45° for a smooth finish.
You can choose from three different sizes of
V-shaped grooves (a).
•
Switch on the tool and wait until it reaches full
speed. Place the required V-shaped groove
(a) on the edge of the workpiece at an angle
of 45°.
•
Now move the electric plane along the edge
of the workpiece.
•
To achieve a good quality result you should
keep the feed speed and angle constant.
6.2.3 Planing steps (Fig. 4/8)
•
The planing of steps is possible with the help
of the parallel stop (11).
•
Mount the parallel stop (11) on the left side of
the tool (see section 5.3).
•
To mount the depth stop, fasten the step
depth scale (10) to the front right side of the
plane housing with the locking lever (9) (see
Fig. 8).
•
Release the locking lever (9) and position
the step depth scale (10) so that the required
step depth is displayed. Pull the locking lever
(9) tight again.
Anl_SA_TC_PL_750_SPK8.indb 30 Anl_SA_TC_PL_750_SPK8.indb 30
GB
Width of step:
You can set the width of the step with the parallel
stop (11).
Depth of step:
We recommend you to set a cutting depth of 2
mm and to keep planing the workpiece until the
required depth of step is reached.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
authorized after-sales service or similarly trained
personnel to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician
and/or an authorized service agent.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician or the
authorized service technician.
- 30 -
02.11.2023 13:30:52 02.11.2023 13:30:52