Bosch GLI 18V-2200 C Professional Manual Original página 12

12 | English
(2) Locking mechanism of the battery cover
(3) Battery cover
(4) Lamp head
(5) Stand
(6) Heat sink
(7) 5/8" tripod mount
(8) Carrying handle
(9) Screw for battery compartment cover
(10) Battery compartment cover
(11) Coin cell
(12) Battery compartment
(13) Rechargeable battery release button
a)
(14) Rechargeable battery
a) This accessory is not part of the standard scope of delivery.
Technical Data
Cordless worklight
Article number
Rated voltage
Max. rated power input
A)
Lighting duration , approx. min/Ah
Total luminous flux, max.
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
B)
ure during operation and
during storage
Coin cell
Recommended rechargeable
batteries
Recommended chargers
Protection class
C)
Protection rating
Data transfer
D)
Bluetooth®
E)
Signal range
Operating frequency range
1 609 92A 9JN | (06.05.2024)
Cordless worklight
Max. transmission power
A) At maximum brightness incl. remaining operating time in
B) Limited performance at temperatures < 0 °C
C) Applies only when battery cover is closed and locked
D) The mobile devices must be compatible with Bluetooth® Low
E) The signal range may vary greatly depending on external condi-
The colour rendition of illuminated objects can be distorted.
Values can vary depending on the product, scope of application and
a)
environmental conditions. To find out more, visit
www.bosch-professional.com/wac.
System requirements
Mobile device (tablet, smart-
phone)
GLI 18V-2200 C
A) Minimum system requirements can be found in the app store for
3 601 D46 5..
V= 18
Rechargeable battery
W 23
Bosch sells some cordless worklights without a re-
44
chargeable battery. You can tell whether a rechargeable bat-
lm 2200
tery is included with the cordless worklight by looking at the
packaging.
°C 0 to +35
Charging the battery
°C –20 to +50
u
V 3
Note: Lithium-ion rechargeable batteries are supplied par-
type CR 2032
tially charged according to international transport regula-
GBA 18V...
tions. To ensure full rechargeable battery capacity, fully
ProCORE18V...
charge the rechargeable battery before using your tool for
(max. 8.0 Ah)
the first time.
GAL 18...
GAX 18... Inserting the Battery
GAL 36...
Unlock the locking mechanism of the battery cover (2) and
/III
fold up the battery cover (3).
IP64
Insert the charged battery (14) into the lamp head (4) until
you feel it engage and it is flush with the lamp head (4).
Close the battery cover (3) and then the locking mechanism
Bluetooth® 4.1
of the battery cover (2).
(Low Energy)
u
m 15
MHz 2402–2480
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
The rechargeable battery has two locking levels to prevent
the battery from falling out if the battery release button is
mW
dimmed mode
Energy devices (version 4.1) and support the Generic Access
Profile (GAP).
tions, including the receiving device used. The Bluetooth® range
may be significantly weaker inside closed rooms and through
metallic barriers (e.g. walls, shelving units, cases, etc.).
Android, iOS
A)
your mobile device (e.g. Google Play Store or Apple App Store).
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
cordless worklight.
Make sure that the rubber lip is seated correctly when
closing the battery cover. Otherwise protection against
dust and splash water will not be ensured.
GLI 18V-2200 C
< 2
Bosch Power Tools