Transport And Storage; Disposal; Functional Accessories And Peripherals; Ec Declaration Of Conformity - Menzer LHS 225 PRO Manual De Instrucciones

7. troubleshooting
problem Possible causes
• The machine is • Plug is not properly plugged into
not functioning or the power outlet.
malfunctioning.
• Defective plug.
• Worn carbon brushes.
• Mains fuse has blown
or tripped.
• The machine produces • Driving disc or abrasive not
too much noise. properly attached.
• The machine vibrates • Filler material or surface to be
too much. sanded is too hard.
• The machine produces • Clogged suction hose.
too much dust.
• Dust bag of the industrial
• Inadequate suction. vacuum cleaner is full.
• Kink in the suction hose.
• Defective brush rim.
• Suction openings not in
same positions.
• Material removal is • Grit size of the abrasive is
too strong. too coarse.
• Poor or not ideal surface • Incorrect or too coarse abrasive
quality throughout the grit size and/or incorrect abrasive.
sanding zone.
• Filler material is not
completely dry.
• Filler material is too soft and/or
very high filler content.
• Grooves in the • Driving disc set at an angle.
sanded surface.
• Filler material is too soft.
12 EN
remedy
• Check plug connection,
connect the plug properly to the
power outlet.
• Use MENZER repair service.
• Attach the driving disc and
abrasive firmly and centred.
• Vary the speed.
• Select other abrasive.
Please take note of our abrasive
overviews or seek advice.
• Clean suction system.
• Empty the bag.
• Eliminate buckling.
• Replace the brush rim.
• Position suction openings in
same positions.
• Select finer grit size.
• Select finer grit size and/or use
other abrasives. Please take note
of our abrasive overviews or seek
advice.
• Take note of the data sheets
and machining instructions of the
manufacturer of the filler material.
• Set the driving disc on flat.
• Select finer grit size.

8. transport and storage

The machine may only be transported in the
original packaging supplied by MENZER. Also
always store the sander in the supplied packaging
and keep it out of the reach of children and keep it
free of moisture.

9. disposal

Not dispose of power tools in household waste!
Machines, their accessories and packaging
should be recycled environmentally friendly in ac-
cordance with national regulations!
Only for EU:
In accordance with European Directive
2002/96/EC on waste electrical and electronic
equipment, power tools must be collected sepa-
rately and disposed of via environmentally friendly
recycling.
10. Functional accessories
and peripherals
Use only the original MENZER accessories
designed for this machine to achieve optimum
results.
1. Extra grip – to vary the range, you can mount
the extra grip in various positions on the main
tube (refer to page *22*)
2. MENZER universal adapter for third-party-
produced equipment with two removable rubber
sleeves for common industrial vacuum cleaner
dimensions (refer to page *22*)
3. Portable vacuum cleaner VC 660 M
(refer to page *23*)
4. Industrial vacuum cleaner VC 760
(refer to page *23*)
5. Industrial vacuum cleaner VC 790 PRO
(refer to page *23*)

11. eC declaration of Conformity

We declare under our sole responsibility that the
machine designated below, brought into circula-
tion by us and described in this operating instruc-
tions complies with the following standards. Any
modifications to the machine not authorized by us
will render this declaration null and void.
Product: Long-neck sander
type: MENZER LHS 225 PRO /
LHS 225 PRO VARIO
Relevant eC directives
2006/42/EC; 2004/108/EC; 2011/65/EU
applied harmonized standards
EN 60745-1; EN 60745-2-3; EN 55014-1;
EN 55014-2; EN 61000-3-2; EN 61000-3-3
Torsten Ceranski
Managing director
Taucha, 01/03/2015
MENZER GmbH
Straße des 17. Juni 4
04425 Taucha
Germany

12. warranty terms and conditions

With the purchase of a MENZER power tool from
the PRO LINE the end user is granted a warranty.
Please visit https://www.menzer-tools.com/service
for the exact warranty terms.
MENZER service
Phone: +49 (0) 342 98 74 14 15
Fax: +49 (0) 342 98 74 14 29
Email: service@menzer-tools.com
No liability for printing errors.
Subject to technical modifications.
EN 13