Publicidad
Idiomas disponibles
Idiomas disponibles
Problem
Dishwasher
not
filling with water
Water
Leaks
Tub stains
Streaks on glass-
ware or residue
on the dishes
Fascia panel
discolored or
marked
Noise during
wash cycle
Detergent dis-
penser cover will
not shut
Unable to select
desired cycle
Error Codes
Water is left in
the appliance
at the end of the
programme
"Check water
supply" display
lights up
Cause
i.
2.
3.
i.
2.
3.
4.
Restriction
in the water supply system.
Previous wash cycle was not completed.
Delay-start
is active.
Suds
Door seal could be pulled away from track.
Condensation
vent is blocked.
Improper
installation.
1.
Stains on the dishwasher
interior
are due to hard-
ness of water.
2.
Silverware
in contact with tub.
Action
1.
Ensure that the water supply valve (typically located under kitch-
en sink) is open and check that the water supply line has no kinks
and clogs.
2.
Refer to the "Canceling or changing the cycle" section of this
manual.
3.
Cancel the delay-start or wait until delay-start time completes
(times out). Refer to the "Delay Start" section of this manual.
1.
Wrong type of detergent
results in suds and leaks. Use only
dishwasher
detergents,
if suds still persist, then add one ta-
blespoon
of vegetable
oil at the bottom
of the dishwasher
and run the desired cycle.
2.
Ensure that door seal is in the track.
3.
Ensure that condensation
vent is not blocked. Refer to "Load-
[ng Extra Tall Items"
[nthe
Preparing and Loadingthe
Dish-
washer section of this manual.
4.
Have proper installation
verified
by qualified
personnel
(wa-
ter supply, drain system, leveling, plumbing).
:1.
Concentrated
Lemon juice can reduce the build up of hard
water stains. Run a normal cycle until it flushes and interrupt
the cycle and then
place an 8 oz. cup of the concentrated
lemon solution
on the top rack and finish the cycle. This can
be done periodically
to avoid build up.
2.
Ensure that the silverware
does not make contact
with the
tub while running
a cycle.
Depending
on the hardness of water, adjust the rinse agent dis-
penser. Refer to "Adding Detergent and Rinse Agent" section in this
manual for adjustment.
Use mild detergents
with soft damp cloth.
Water circulation
sound is normal,
but if you suspect items are
banging into each other or into the spray arms, refer to the "Pre-
paring and Loading"
section of this manual for optimal
arrange-
ment.
:1.
Refer to "Adding Detergent and Rinse Aid" section of this man-
ual for instructions
on opening and closing the dispenser.
2.
Refer to the "Canceling
or changing the cycle" section of this
manual.
Incorrect
rinse agent setting.
Abrasive cleaner used.
The dishes may not be arranged properly.
:1.
Improper
operation
of detergent
coven
2.
Previous cycle has not been finished,
reset, or cycle
was interrupted.
Previous cycle has not finished or another
cycle has
Refer to the "Canceling
or changing the cycle" section of this
already started,
manual.
If fault code (EO:1to E30) is indicated
on the digital display 3, first disconnect
the appliance from the power supply. You can
rectify certain faults yourself
(see following
fault description),
for all other faults please contact customer service and state the
indicated fault E:XX.
:1.
:1.
See Care and Maintenance.
2.
2.
Wait until programme
ends (digital display indicates 0:00) or
implement
the "Reset'function.
3.
4.
(E24) Waste water hose is blocked or kinked.
(E25) Waste water pump blocked, cover on the
waste water pump is not locked in position
Filters blocked.
The programme
has not yet ended.
:1.
Tap turned off.
2.
Water supply interrupted.
3.
Supply hose kinked.
4.
Filter in the water supply blocked
:1.
Switch off the appliance and pull out the main plug.
2.
Turn off the tap.
3.
Clean filter in the supply hose.
LJ
4.
Reconnect
power supply.
5.
Turn on the tap.
6.
Switch on the appliance.
2O
Publicidad
