Publicidad
Idiomas disponibles
Idiomas disponibles
EngLIsh
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
Mounting Torque Tester to a Surface (Fig. B, C)
This tool is designed to be mounted to a table or work surface
prior to use. Ensure its mounted within reach of an electrical
outlet. Make sure the mounting method is suitable for the surface
type and is appropriate to the application of the tool.
1. Use the bottom of the tool as a template for the location of
the mounting hardware holes. See Fig. B for details.
2. Mark the location of the four 3/8" (10 mm) mounting
holes
14
on the surface (within reach of an electrical
outlet as shown in Fig. C.
3. Secure the tool to the surface using appropriate hardware
for the chosen surface material, and the weight of the tool.
Powering on and off (Fig. A)
1. To power on, press the power button
with an audible beep and then power on.
2. To switch off, press and hold the power button
will signal with an audible beep and then power off.
nOTE: After sitting idle for two minutes the tool will signal
with an audible beep and then power off automatically.
Before Using the Torque Tester (Fig. A)
1. Plug the AC/DC power adapter
60 Hz electrical outlet.
2. Plug the AC/DC jack plug
into the AC/DC power port
Power on and zeroing the torque tester
1. Press the power button
2. Press and hold the zero reset button
tester before using the tool.
nOTE: Your LCD screen
Auto power off
1. To conserve energy, after sitting idle for two minutes the
tool will signal with an audible beep and then power
off automatically.
2. Press the power button
hardware reset
WARNING: If
been torqued to more than 110% of its maximum
torque capacity.
14
. The tool will signal
8
8
. The tool
3
into any standard 120 Volt
of the AC/DC power adapter
4
2
of the tool.
8
to power on the tool.
12
to zero the torque
5
will appear as shown
8
to power on the tool.
appears, it means this tool has
1. To do hardware reset, use a pin to touch the system reset
button
7
and then press the power button
the tool.
setting Target Torque
1. To set target torque, press and hold the target button
until
is displayed on the LCD screen
you are adjusting the target torque.
2. Press the mode selection button
target torque.
3. Press the unit switch button
target torque.
4. To exit this screen mode press the target button
is displayed on the LCD screen
will appear as shown
setting Tolerance Percentage
1. To set tolerance percentage, press and hold the target
button
9
until
2. Press the target button
is displayed on the LCD screen
are adjusting the tolerance percentage.
3. Press the mode selection button
level tolerance
4. Press the unit switch button
level tolerance.
5. To exit this screen mode press the target button
is displayed on the LCD screen
will appear as shown
setting Idle to sleep seconds
1. To set idle sleep time, press and hold the target button
until
is displayed on the LCD screen
2. Press the target button
is displayed on the LCD screen
are adjusting the idle sleep time.
3. Press the mode selection button
sleep time.
4. Press the unit switch button
sleep time.
5. To exit this screen mode press the target button
3
is displayed on the LCD screen
will appear as shown
Displaying Over-torque Percentage
1. To see the over‑torque percentage, press and hold
the target button
LCD screen
.
2. Press the target button
is displayed on the LCD screen
are viewing the over‑torque percentage.
3. To exit this screen mode press the target button
is displayed on the LCD screen
will appear as shown
to increase the
11
10
to decrease the
5
.
is displayed on the LCD screen
9
to cycle through the menu until
5
11
to adjust the upper
10
to adjust the lower
5
.
9
to cycle through the menu until
5
11
to increase the idle
10
to decrease the idle
5
.
9
until
is displayed on the
5
.
9
to cycle through the menu until
5
5
.
8
to power on
9
5
. This indicates
9
until
. Your LCD screen
5
5
.
. This indicates you
9
until
. Your LCD screen
5
9
5
.
. This indicates you
9
until
. Your LCD screen
5
. This indicates you
until
9
. Your LCD screen
5
Publicidad
