Publicidad
Idiomas disponibles
Idiomas disponibles
7
8
Coffee lever
9
Heating elements
10
activation LED
11
Cup warmer button
12
Hot water tap
13
Hot water regulating valve
14
Pump operation LED
15
Cup holder
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
Control panel
(Fig. 3 on page 3)
1. Espresso
2. Double espresso
3. Two espressos
4. Two double espressos
5. Continuous mode/programming
(Fig. 4 on page 3)
Semi-automatic models have a dedicated ON/OFF switch above
each group.
Spare parts or accessories
1. 80 cm water inlet hose
2. Drain hose with 1 elbow pipe
3. 1 dummy plug for portafilters
4. 1 cleaning brush
Necessary connections
• 1 water inlet valve with G3/8 nut (for connecting the water
inlet hose)
• 1 water drain with a water drainage pipe - diameter min. 16-
17 mm
• 1 grounded electrical socket with 30 mA protection and 20 A
residual current device
• If the appliance is not connected to the water supply, whose
pressure is below 1 bar at the inlet, use the non-return valve
on the water supply hose preventing backflow of water.
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
Control panel
Heating switch
Main switch
Hot water tap
Hot water regulating valve
Cup warmer
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Starting coffee preparation
Models 207499, 207581
During the first filling of the device with water, heating will only
start after reaching the minimum water level and when the
green LED goes off. In other case, heating will work continously
(except when the water level drops below the minimum level
and the device is locked).
• Open the valve, allowing the device to fill with water.
• Press the ON/OFF switch.
• Check the pressure gauges. When the orange LED goes out,
the pressure in the boiler must be approx. 1 bar (approx. 0.1
MPa). The pump pressure must be approx. 9 bar (approx. 0.9
MPa). To adjust the pump pressure, turn the screw on the
top of the pump.
• Before starting work, clean the steam nozzles by turning the
valve to the right. The nozzles will open. The steam should
flow freely through the nozzle for a few seconds, cleaning it.
Then turn the nozzle valve to the closed position. Clean all
nozzles of the device in this way.
Models 207598, 207642, 207659
• Press the appliance power button.
• The green LED will be on when water is being drawn and will
go off when the water reaches a certain level. When starting
the device for the first time, the heating can only be turned on
when the green LED goes out.
• After filling the boiler, press both switches at the same time
• Turn on the water heating - the orange diode will light up.
The LED will turn off when the water temperature reaches
a certain level.
• Water pressure in the boiler after heating should be approx.
1 bar. The pressure in the system is indicated by the manom-
eter.
• Before starting work, clean the steam nozzles by turning the
valve to the right. The nozzles will open. The steam should
flow freely through the nozzle for a few seconds, cleaning it.
Then turn the nozzle valve to the closed position. Clean all
nozzles of the device this way.
Coffee portion programming
Models 207499, 207581
Models equipped with a flow meter, thanks to which succes-
sive portions of coffee are measured, allow you to program the
amount of each drink.
• Always start programming the number of drinks with the
group on the left. The setting programmed for the first group
is carried over automatically to the next ones. It is also possi-
ble to program each group separately.
• Fill the lever with the correct amount of ground coffee and
place it in the group.
• Press and hold button 5 (fig. 3/pos. 5) for 3 seconds to switch
the device to programming mode. The button LED will flash
and all other LEDs on the keypad will light up. The device is
ready for programming.
• Within 5 seconds, press the button of the function you want to
program (fig. 3/pos. 1-4). The LED of the selected button and
GB
7
Publicidad
