Descargar Imprimir esta página

Mitsubishi Electric CITY MULTI PLFY-P VCM-E2 Serie Manual De Instrucciones página 4

Ocultar thumbs Ver también para CITY MULTI PLFY-P VCM-E2 Serie:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 82
2. Parts Names
Wired Remote-Controller (Optional parts)
Display Section
For purposes of this explanation,
all parts of the display are shown
as lit. During actual operation,
only the relevant items will be lit.
Identifies the current operation
Shows the operation mode, etc.
* Multi language display is
supported.
"Centrally Controlled" indicator
Indicates that operation of the
remote controller has been
prohibited by a master controller.
"Timer is Off" indicator
Indicates that the timer is off.
Temperature Setting
Shows the target temperature.
Operation Section
Temperature set buttons
Down
Up
Timer Menu button
(Timer monitor/Timer set button)
Operation mode button
(Back button)
Set Time buttons
Back
Ahead
Timer On/Off button
(Set Day button)
Opening the
cover
Note:
"PLEASE WAIT" message
This message is displayed for approximately 3 minutes when power is supplied to the indoor unit or when the unit is recovering from a power failure.
Operation mode flashing display
When multiple indoor units are connected to a single outdoor unit and an operation mode is selected for one indoor unit that is different from the
current operation mode of another indoor unit, the operation mode display flashes. Select the same operation mode of the other indoor unit.
"NOT AVAILABLE" message
This message is displayed if a button is pressed to operate a function that the indoor unit does not have.
When the same remote controller is used to operate multiple indoor units, this message is displayed if the main indoor unit is not equipped with
the selected function.
Room temperature display
The indoor unit temperature sensors or the remote controller temperature sensor can be selected to measure the room temperature. The indoor
unit temperature sensors are the initial setting. When the indoor unit temperature sensors are selected to measure the room temperature, the
room temperature measured at the main indoor unit is displayed on the remote controller that operates multiple indoor units.
4
Day-of-Week
Shows the current day of the week.
Time/Timer Display
Shows the current time, unless the simple or Auto Off
timer is set.
If the simple or Auto Off timer is set, shows the time
remaining.
TIME SUN MON TUE WED THU FRI SAT
TIMER
AFTER
ERROR CODE
°F°C
ONLY1Hr.
Airflow up/down direction indicator
The indicator
shows the direction
of the outcoming airflow.
"One Hour Only" indicator
Displayed if the airflow is set to Low
and downward during COOL or DRY
operation mode. (Operation varies
according to model.)
The indicator goes off after one hour
when the airflow up/down direction
also changes.
TEMP.
MENU
ON/OFF
BACK
MONITOR/SET
DAY
PAR-21MAA
CLOCK
Hr
ON
AFTER
OFF
FUNCTION
°F°C
FILTER
WEEKLY
SIMPLE
AUTO OFF
Room Temperature display
Shows the room temperature. The room
temperature display range is 8–39 °C.
The display blinks if the temperature is
less than 8 °C or 39 °C or more.
Louver display
Indicates the action of the swing louver.
Does not appear if the louver is
stationary.
(Power On indicator)
Indicates that the power is on.
ON/OFF
FILTER
CHECK
TEST
OPERATION
CLEAR
Built-in temperature sensor
"Sensor" indicator
Displayed when the remote controller
sensor is used.
"Locking function" indicator
Indicates that remote controller
buttons have been locked.
"Clean the filter" indicator
Comes on when it is time to clean
the filter.
Timer indicators
The indicator comes on if the
corresponding timer is set.
Fan Speed indicator
Shows the selected fan speed.
Ventilation indicator
Appears when the unit is running in
Ventilation mode.
ON/OFF button
Fan Speed button
Filter
button
(<Enter> button)
Test Run button
Check button
(Clear button)
Airflow up/down button
Louver button
(
Operation button)
To preceding
operation number.
Ventilation button
(
Operation button)
To next operation
number.

Publicidad

loading