Bontempi 15 3770 Libro De Instrucciones página 8

E N G L I S H
POWER SUPPLY VIA USB TYPE-C SOCKET
The product can be powered using the standard USB
type-C socket, Vdc = 5V
below:
WARNING: All batteries or transformers with safety insulation must be
checked regularly for faults in cable, wire, or plug insulation or other parts.
This instrument is only to be connected to equipment
bearing either of the following symbols:
NOTE: Rating plate information was located at bottom enclosure of the
apparatus.
BATTERY SUPPLY
Use a screwdriver to open the battery compartment.
Insert 4 x 1.5 V batteries R6/AA (not supplied), ensu-
ring correct polarity (+/–). Re-fit battery cover.
Replace batteries when the quality of sound beco-
mes bad. Use alkaline batteries to obtain a longer
duration.
ATTENTION - BATTERY CARE
• Non-rechargeable batteries are NOT to be
recharged. • Rechargeable batteries must
be removed from the product before being
charged. • Rechargeable batteries are only
to be charged under adult supervision. •
Different types of batteries or new and old
batteries are not to be mixed. • Use only batteries of the same or equivalent
type. • Batteries are to be inserted with correct polarity. • Remove exhausted
batteries to prevent leakage. • Do not short circuit supply terminals. •
Remove batteries during long periods of non-use.
WASTE DISPOSAL STANDARDS
For information regarding the disposal of the items mentioned here below,
please refer to Council Administration office regarding specialised waste
collection centres.
1. DISPOSAL OF BATTERIES:
Protect the environment by disposing of batteries in the special containers
provided for this use.
2. PACKAGING DISPOSAL: Take the paper, cardboard
and corrugated board to the appropriate waste
collection centres. Plastic material must be placed in
the relevant collection containers.
The symbols indicating the various types of plastic are:
01 02 03
PET PE PVC
Key for the different types of plastic materials:
PET= Polyethylene terephtalate • PE= Polyethylene, code 02 for PE-HD, 04
for PE-LD • PVC =Polyvinyl chloride • PP= Polypropylene • PS= Polystyrene,
Polystyrene foam • O= Other polymers (ABS, Laminates, etc.)
6
; I = 1A as shown in the figure
05 06 07
PP PS O
3. DISPOSING OF ELECTRICAL APPLIANCES: The wheelie bin symbol with a
cross indicates that the product must not be disposed of in the domestic
waste at the end of its useful life. Instead, it should be taken to
your nearest designated collection point or recycling facility.
Alternatively, check with your retailer and return the product
when buying a replacement, on a one-to-one basis or as free
of charge in case the size is smaller than 25 cm. Appropriate
disposal promotes the recycling of parts and materials, as well as helping to
protect the environment and human health. Under current legislation, strict
penalties are enforced against those disposing of products illegally. For more
information about the collection of special waste, contact your Local
Authority.
SWITCHING ON/OFF
To switch on the instrument move selector
switch the instrument off, move the same selector to
OFF.
DEMOSONGS
This keyboard has 10 demosongs. To choose the pre-
recorded tracks, press the DEMO key
a
Press STOP
to interrupt.
VOLUME CONTROL
Adjust volume to desired level by using the VOLUME
b
buttons .
SOUNDS
The instrument features 8 sounds.
To select the sounds, press the SOUNDS
cession. Poliphony: 8 notes.
SUSTAIN
Prolongs the sound of a note when the key is released.
To enable or disable this function, press SUSTAIN
VIBRATO
The vibrato effect is a sound modulation.
To enable or disable this function, press VIBRATO
RHYTHMS
The instrument features 16 rhythms.
To select the rhythms, press the RHYTHMS
succession.
Press the TEMPO buttons
the rhythm speed. Press STOP
RECORD/PLAYBACK FUNCTION
This function enables you to record and playback a tune
played on the keyboard. Press REC.
tune. When you have finished press PLAY
the tune.
å
to ON. To
r
in succession.
d
key in suc-
c
key in
g
to reduce (–) or increase (+)
a
to interrupt.
e
before playing a
f
to listen to
n
.
m
.