Publicidad
Idiomas disponibles
Idiomas disponibles
The machine is used for:
For the sawing, longitudinally and transversely, of
solid wood, chipboard, plywood, plastic, aluminium
by using the TCT or HSS saw blade. For sawing tiles,
printed circuit boards or glass fiber reinforced plastic
must be used the diamond saw blade.
WARNING:
• Use only saw blades allowable for this machine!
• Never use a damaged saw blade!
• Use the machine never with defective or without
mounted guard
Ambient conditions
The machine may be operated:
humidity
max. 70%
temperature
from +5°С to +40°С
The machine shall not be operated in areas exposed
to increased fire or explosion hazard.
Prohibited use
• The operation of the machine outside the stated
technical limits described in this manual is forbid-
den.
• Operation of the machine function without emer-
gency device is prohibited.
• The use of the machine not according with the re-
quired dimensions is forbidden.
• The use of the machine not being suitable for the
use of the machine and not being certified is for-
bidden.
• Any manipulation of the machine and parts is for-
bidden.
• The use of the machine for any purposes other
than described in 12.1 is forbidden.
• The unattended operation on the machine during
the working process is forbidden!
• It is not allowed to leave the immediate work area
during the work is being performed.
m Please note that our equipment has not been de-
signed for use in commercial, trade or industrial ap-
plications. Our warranty will be voided if the machine
is used in commercial, trade or industrial businesses
or for equivalent purposes.
5. General safety instructions for
power tools
• WARNING Read all warnings and instructions.
Failure to apply all warnings and instructions can
lead to electrical shock, fire and/or serious injury.
• Keep all warnings and instructions handy for
future consultation.
• The term "power tool" used in the warnings refers
to power tools that are connected to a source of
electrical energy (with an electrical cable)
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
1) Workplace safety
a.) Keep your working area clean and well lit. Clut-
tered or dimly lit workspaces can lead to acci-
dents.
b.) Do not operate power tools in areas where explo-
sions could take place, or in which flammable liq-
uids, gases or dust are present. Power tools can
create sparks, which can cause dust or fumes
to ignite.
c.) Keep children and bystanders away from the
power tool when it is being used. Distractions
could cause you to lose control over the equip-
ment.
2) Electrical safety
a.) The terminal plug of the tool must fit into the out-
let. The plug may not be modified in any way. Do
not use an adaptor plug together with grounded
power tools. The original plugs and the appropri-
ate outlets reduce the risk of an electrical shock.
b.) Avoid contact with grounded surfaces, such as
pipes, radiators, stoves and refrigerators. There
is an increased risk of electrical shock, if your
body is grounded.
c.) Keep power tools away from rain or wet condi-
tions. Penetration of water into the power tool
increases the risk of electrical shock.
d.) Do not use the cable for any purpose other than
that for which it was made. Do not use it to carry
the tool, hang it up, or to pull the plug out of the
outlet. Keep the cable away from heat, oil, sharp
corners or parts of the equipment that move.
Damaged or entangled cords increase the risk
of electrical shock.
e.) When operating the power tool outdoors, only
use extension cords that are suitable for outdoor
use. The use of an appropriate extension cord
reduces the risk of an electrical shock.
f.) If the power tool must be used in a damp envi-
ronment, use a residual current protective de-
vice. The use of such a device reduces the risk
of electrical shock.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can im-
pair active or passive medical implants under certain
conditions. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
GB | 19
Publicidad
