Publicidad
Idiomas disponibles
Idiomas disponibles
g.) Always use the correct size of saw blades and
make sure they have the right locating bore (e.g.
Star shaped or round). Saw blades that do not fit
the assembly of the saw do not run correctly and
cause loss of control.
h.) Never use damaged or incorrect saw blade shims
or screws. The saw blade shims and screws are
designed especially for your saw, for optimal per-
formance and operating safety.
i) Wear suitable protective equipment such as ear
protection, safety goggles, a dust mask for work
which generates dust, and protective gloves when
working with raw materials and when changing
tools.
7. Additional safety instructions for
all saws
Causes and prevention of kickbacks:
• A kickback is a sudden reaction due to a caught,
jammed or incorrectly adjusted saw blade, which
leads to the saw rearing up in an uncontrolled
manner and moving out of the work piece towards
the operator.
• If a saw blade catches or jams in the sawing edge
that closes behind it, it is blocked and motor's drive
pushes the saw back in the direction of the op-
erator.
• If the saw blade twists in the saw groove or is in-
correctly positioned, the teeth at the rear side of
the saw blade edge catch in the surface of the
work piece. The saw then moves out of the saw
groove and springs back in the direction of the
operator.
• A kickback results from an incorrect or faulty use
of the saw. It can be prevented, as will be de-
scribed in the following, by appropriate caution-
ary measures.
a.) Hold onto the saw and position your arms so that
they can absorb any energy from a kickback. Al-
ways keep to the side of the saw blade, and never
bring it into line with your body. In the case of a
kickback, the circular saw can jump backwards,
but with adequate caution the operator can deal
with the energy of the kickback.
b.) If the saw blade jams or you want to interrupt your
work, then turn the saw off and keep the work
piece still until the saw blade comes to a full stop.
Never try to remove the saw from the work piece
or pull it out when the saw blade is moving since
then a kickback can occur. Find out the cause of
the jam and remove it.
c.) If you want to start up a saw that is in the work
piece, centre the saw blade in the sawed groove
and check that the saw blade teeth are not caught
in the work piece.
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
If the saw blade is jammed, it can jump out of
the work piece or cause a kick back when it is
started up.
d.) Support larger work pieces in order to reduce the
risk of a kick back due to a saw blade jam. The
weight of larger work pieces can cause them to
bend. Large pieces must be supported on both
sides, both near the sawing slot as well as on
the edges.
e.) Do not use dull or damaged saw blades. Saw
blades with dull or misaligned teeth increase the
friction, in the sawing slot, cause saw blade jams
and kickbacks.
f.) Before you start sawing, tighten the adjustments
for the cut depth and angles. If you change set-
tings while sawing, the saw blade can jam and a
kickback is the result.
g.) Be particularly careful when making "inserted
cuts" in walls that already exist or other areas
where you cannot see what is behind the sur-
face. When the saw blade is inserted into the wall
it can be blocked by hidden objects and cause
a kick back.
8. Safety instructions for inserted
circular saw use
INSTRUCTIONS FOR ALL SAWS
• Make sure that the dust catching mechanism is
correctly installed, as is described in this manual.
• Wear breathing protection.
• Only those saw blades recommended in the man-
ual should be used.
• Always wear ear protection.
• Replace the saw blades as described in this man-
ual.
• The maximum cut depth is 28,5 mm.
If the electrical cable of this tool is damaged it must
be replaced by the manufacturer or the customer
service department or a similarly qualified specialist
in order to avoid dangers.
Further Special safety Instructions for Circular
Saws
Only use the recommended saw blades which cor-
respond to EN 847-1.
Do not use any saw blades which do not correspond
to the characteristics described in these operating in-
structions. Saw blades may not be brought to a stop
by pressure on the machine from the side.
Make sure that the saw blade is tightly assembled
and turns in the correct direction.
GB | 21
Publicidad
