Publicidad
Idiomas disponibles
Idiomas disponibles
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool
with another.It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for
different applications, with different accessories or poorly
maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This
may significantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of
work patterns.
3. Assembly
Changing the Tool
l Wear protective gloves when changing application
tools/accessories. Contact with the application
tool/accessoriy can lead to injuries.
Selecting the Application Tool/Accessory
Accessory
HSS wood
segment saw
blade
BIM segment saw
blade
HSS plunge cut
saw blades, wood
BIM plunge cut
saw blades, metal
BIM plunge cut
saw blade, wood
and metal
Base plate for
sanding, series
Delta 93 mm.
Mounting/Replacing the Application Tool/ Accessory
180 Turn the lever 7 to extract useful and change it. Re turn
around to fix the tool.I
ENGLISH
13
Material
Wooden materials,
plastic
Wooden materials,
plastic.
Wooden materials,
plastic, gypsum and
other soft materials
Metal (e.g.
unhardened nails,
screws, smaller
profiles), non-
ferrous metals
Wood, metal, non-
ferrous metals
Depends on
sanding sheet
13
Check the tight seating of the application
l
tool/accessory. Incorrect or not securely fastened
application tools/accessories can come loose during
operation and pose a hazard.
Mounting/Replacing a Sanding Sheet on the Sanding
Plate
The sanding plate is fitted with Velcro backing for quick and
easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet, free the Velcro backing
of the sanding plate from any debris by tapping against it in
order to enable optimum adhesion.
Position the sanding sheet flush alongside one edge of the
sanding plate , then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
To remove the sanding sheet, grasp it at one of the tips and
pull it off from the sanding plate.
Selecting the Sanding Sheet
Depending on the material to be worked and the required
rate of material removal, different sanding sheets are
available:
Sanding disc
Red quality
Application
For coarse-sanding, e.g. of rough,
unplaned beams and boards
For face sanding and planing small
irregularities
For finish and fine sanding of wood
Dust/Chip Extraction
l Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful
to one's health. Touching or breathing-in the dusts can
cause allergic reactions and/or lead to respiratory
infections of the user or bystanders.
Certain dusts, such as oak or beech dust, are
considered as carcinogenic, especially in connection
with wood-treatment additives (chromate, wood
preservative). Materials containing asbestos may only
be worked by specialists.
– As far as possible, use a dust extraction system
suitable for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filterclass respirator.
Observe the relevant regulations in your country for the
materials to be worked..
Material
- All wooden
materials (e.g.,
hardwood, softwood,
chipboard, building
board)
- Metal materials
Grain size
coarse
60
medium
120
fine
210
Publicidad
