Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
11. HANGING BRACKET: with 2 knobs on both sides to fasten the unit and a mounting
hole to fix a mounting hook.
12. LASER OUTPUT: Here the laser beam leaves the enclosure, make sure to NEVER
look inside the unit through this opening while the laser effect is switched on!
13. WARNING LABEL: "Caution – Class 3B laser. Laser Radiation when open. Avoid
exposure to beam."
14. WARNING LABEL: "Laser Aperture"
15. LASER WARNING SIGN: warns against a potentially dangerous laser when not used
by skilled operators.
16. WARNING LABEL: "Laser Radiation. Avoid exposure to beam. Class 3B laser
product"
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only.
Improper installation can result in serious injuries and/or damage to property.
Overhead rigging requires extensive experience! Working load limits should be
respected, certified installation materials should be used, the installed device
should be inspected regularly for safety.
Make sure the area below the installation place is free from unwanted persons during
rigging, de-rigging and servicing.
Locate the fixture in a well ventilated spot, far away from any flammable materials and/or
liquids. The fixture must be fixed at least 50cm from surrounding walls.
The device should be installed out of reach of people and outside areas where persons
may walk by or be seated.
Before rigging make sure that the installation area can hold a minimum point load of
10times the device's weight.
Always use a certified safety cable that can hold 12times the weight of the device when
installing the unit. This secondary safety attachment should be installed in a way that no
part of the installation can drop more than 20cm if the main attachment fails.
The device should be well fixed; a free-swinging mounting is dangerous and may not be
considered!
Don't cover any ventilation openings as this may result in overheating.
The operator has to make sure that the safety-relating and machine-technical
installations are approved by an expert before using them for the first time. The
installations should be inspected every year by a skilled person to be sure that safety is
still optimal.
CAUTION EYEDAMAGE: Always position the laser in a way that
prevents the audience from looking directly into the laser beams. The
installation should assure that the beam will not strike the audience.
JB SYSTEMS®
USER MANUAL
5/45
SPACE 2 Laser
ENGLISH
HOW TO SET UP AND CONTROL THE UNIT
Regular breaks during operation are essential to maximize the life of this device as it is
not designed for continual use.
Do not switch the unit on and off in short time intervals as this reduces the lamp life.
Always unplug the unit when it is not used for a longer time or before servicing.
In the event of serious operating problems, stop using the fixture and contact your dealer
immediately.
Important: Never look directly into the laser beam! Don't use the effect in the presence
of persons suffering from epilepsy.
You can operate the unit in 2 ways:
1) AUTOMATIC STAND-ALONE MODE:
Put switch auto/music switch (4) in "auto" position.
Switch the unit on with the power switch (1) and/or key actuated on/off switch (2).
2) MUSIC CONTROLLED STAND-ALONE MODE:
Put switch auto/music switch (4) in "music" position.
Switch the unit on with the power switch (1) and/or key actuated on/off switch (2).
Put on some rhythmic music at the desired level.
Turn the music sensitivity potentiometer until the laser beam nicely follows the beat of
the music.
MAINTENANCE
Make sure the area below the installation place is free from unwanted persons during
servicing.
Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
All screws used for installing the device and any of its parts should be tightly fastened
and may not be corroded.
Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally
free from any deformation.
When an optical lens is visibly damaged due to cracks or deep scratches, it must be
replaced.
The mains cables must be in impeccable condition and should be replaced immediately
when even a small problem is detected.
In order to protect the device from overheat the cooling fans (if any) and ventilation
openings should be cleaned monthly.
The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surroundings can cause
greater accumulation of dirt on the unit's optics.
Clean with a soft cloth using normal glass cleaning products.
Always dry the parts carefully.
Clean the external optics at least once every 30 days.
JB SYSTEMS®
USER MANUAL
6/45
SPACE 2 Laser
Publicidad
