Publicidad
Idiomas disponibles
Idiomas disponibles
English
Operation
Power on
- Press any key to power on the console when being in sleep mode��
- Start pedalling to power on the console when being in sleep mode�
Power off
Without any signal being transmitted into the monitor for 4 minutes
the monitor will enter SLEEP mode automatically� ( Active training
data will be lost )
Programs
Workout target setting
- Press MODE key to cycle between the functions of: TIME,
DISTANCE, KCAL & PULSE�
- Use SET key to set the target for your planned workout�
Press 1 time briefly to increase value with one unit at the time�
Press and hold to increase value rapidly�
- Use RESET key to clear the displayed target mode�
TIME TARGET MODE:
- Setting range:
1:00 ~ 99:00
- Setting units:
1:00 Minute
DIST TARGET MODE:
- Setting range:
0�0 ~ 99:5
- Setting units:
0�5 KM
KCAL TARGET MODE:
- Setting range:
10 ~ 9990 +10
- Setting units:
10 Kcal�
PULSE TARGET MODE:
- Setting range:
0 -3 0 ~ 230
- Setting units:
1 Bpm
NOTE
• When leaving a target setting 0, it will not be seen as a target�
Console function in target mode
- Start pedalling to start the workout at any time, and non set target
values will count up�
- If a target is set for a specific value, that value will countdown, till
target is reached�
- When target is reached, an beep-chimes alarm will sound shortly
go notify you have reached your goal, and that specific parameter
value will continue to count up when keep working out�
- When a pulse limit is set a beep-chimes alarm will sound when
measured pulse exceeds the set pulse limit to notify your measured
heart rate is over set target�
Bluetooth & APP
- This console can connect with an APP on a smart device by
Bluetooth (iOS & Android)�
- Establish the Bluetooth connection only via the connection mode
on the installed APP on your smart device�
- When the bluetooth connection between APP and console is
established the console display will be dimmed�
NOTE
• Tunturi only provides the option to connect your fitness console
throughout a bluetooth connection� Therefore Tunturi cannot
be held responsible for damage, or malfunctioning of products
other than Tunturi products�
• Check the website for extra information�
This console can receive a Bluetooth heart-rate transmitter�
There is no need to pair the device, as the console will auto detect
the heart-rate transmitter when it is in range�
Cleaning and maintenance
The equipment requires very little maintenance, please follow up on
below instructions� The equipment does not require recalibration
when it is assembled, used and serviced according to the instructions�
WARNING
• Do not use solvents to clean the equipment�
• Clean the equipment with a soft, absorbent cloth after each use�
• Regularly check that all screws and nuts are tight�
Defects and malfunctions
Despite continuous quality control, defects and malfunctions caused
by individual parts can occur in the equipment� In most cases, it will
be sufficient to replace the defective part�
- If the equipment does not function properly, immediately contact
the dealer�
- Provide the model number and the serial number of the equipment
to the dealer� State the nature of the problem, conditions of use
and purchase date�
Trouble shooting:
- When the display of LCD is dim, it means the batteries need to be
changed�
- If there is no signal when you pedal, please check if the cable is
well connected�
NOTE
• When stop training for 4 minutes, the main screen will be off�
• If the computer displays abnormally, please re-install the
batteries and try again�
Shaky or unstable feeling during use
If the machine feels unstable or unstable during operation, it is
advisable to adjust the support feet to bring the frame to the correct
height� Read the instructions in this manual in section: "Use"
Transport and storage
WARNING
• Carry and move the equipment with at least two persons�
- Remain standing in front of the equipment on each side and take
a sturdy grip at the handlebars� Tilt the front of the equipment
so as to lift the rear of the equipment on the wheels� Move the
equipment and carefully put the equipment down� Place the
equipment on a protective base to prevent damage to the floor
surface�
- Move the equipment carefully over uneven surfaces� Do not move
the equipment upstairs using the wheels, but carry the equipment
by the handlebars�
- Store the equipment in a dry place with as little temperature
variation as possible�
1 8
Publicidad
