Publicidad
Idiomas disponibles
Idiomas disponibles
English
LED (Red) blinks
LED (Red) lights
Other functions
(6)
In case of operation error, LED lamps show as below.
LEDs blink*
1
(Red)
(1 sec.
interval.)
LEDs blink*
1
(0.5 sec.
(Red)
interval.)
LEDs blink
(Red)
(Orange)
LEDs blink
(Red)
*1 After 10 seconds, automatically turns off LED light and
Power switch.
2. Trigger Lock Mechanism (See Fig. 9)
WARNING
○ Make sure the trigger is locked when not firing staples.
○ This Stapler has a lock mechanism to prevent the
staples from being fired.
○ Set the switch lock lever at the
trigger.
○ Slide the switch lock lever to the
Stapler is to be used, and to the
not in use.
3. Testing the stapler
WARNING
○ Make sure the trigger is locked when not firing staples.
(See Fig. 9)
○ Never use Stapler unless push lever is operating
properly.
Before actually beginning the stapling work, test the
Stapler by using the checklist below. Conduct the tests
in the following order.
If abnormal operation occurs, stop using the Stapler
and contact a HiKOKI authorized service center
immediately.
The battery remaining
power is nearly empty.
The battery remaining
power is empty.
Recharge the battery as
soon as possible.
Machine is in too hot
condition.
Allow the stapler to
cool thoroughly in
adequate condition.
Machine is in too
cold (below -5°C)
condition.
Allow the stapler to
warm-up thoroughly
in adequate
condition.
Error is occurred.
Once remove the
battery. Then attach
the battery and
power ON again.
Contact HiKOKI for
inspection.
position to lock the
position when the
position when it is
REMOVE ALL STAPLES AND BATTERY FROM
(1)
STAPLER.
–
ALL SCREWS MUST BE TIGHTENED.
–
THE PUSH LEVER AND TRIGGER MUST MOVE
SMOOTHLY.
Installing the battery. Do not operate the push lever or
(2)
trigger while installing the battery. (See Fig. 3)
(3)
Turn on the Power switch. (See Fig. 5)
If the battery indicator is lighting or blinking in red, the
battery doesn't have enough power and it needs to be
charged.
(4)
Make sure that the stapling operation indicator is
lighting Blue. (SINGLE SEQUENTIAL ACTION
MECHANISM)
(5)
Remove the finger from the trigger and press the push
lever against the workpiece.
–
THE STAPLER MUST NOT OPERATE.
Separate the push lever from the workpiece.
(6)
Next, point the stapler downward, pull the trigger and
then wait in that position for 5 seconds or longer.
–
THE STAPLER MUST NOT OPERATE.
(7)
A: Without touching the trigger, depress the push lever
against the workpiece. Next, pull the trigger.
–
THE STAPLER MUST OPERATE.
B: Hold the trigger back and depress the push lever
against the workpiece again.
–
THE STAPLER MUST NOT OPERATE.
C: Separate the finger from the trigger. Next, A is operated
again.
–
THE STAPLER MUST OPERATE.
(8)
Separate the push lever from the workpiece, pull the
trigger.
Depress the push lever against the workpiece within
2 seconds.
–
THE STAPLER MUST NOT OPERATE.
(9)
Set the stapling operation indicator blinking ON mode.
(CONTACT ACTUATION MECHANISM) (Fig. 8)
Push the stapling operation switch once, make sure that
the indicator is blinking Blue. Separate the push lever
from the workpiece, pull the trigger. Depress the push
lever against the workpiece within 2 seconds.
–
THE STAPLER MUST OPERATE.
If no abnormal operation is observed, you may load
(10)
staples in the Stapler.
Drive staples into the workpiece that is the same type to
be used in the actual application.
14
Publicidad
