Publicidad
Idiomas disponibles
Idiomas disponibles
12. Press the staple outlet firmly against the material
to be stapled.
When driving in staples, press the staple outlet firmly
against the material to be stapled. If the outlet is not
applied properly, the staples may rebound.
13. Keep hands and feet away from the firing head
when using.
It is very dangerous for a staple to hit the hands or feet
by mistake.
14. Beware of the tool's kickback.
Do not approach the top of the tool with your head etc.
during operation. This is dangerous because the tool
may recoil violently if the staple currently being driven in
comes into contact with a previous staple or a knot in
the wood.
15. Be careful of double fire due to recoil.
If the push lever is unintentionally allowed to re-contact
the workpiece following recoil, an unwanted fastener
will be driven.
In order to avoid this undesirable double fire,
○ Intermittent operation (Trigger firing)
1) Set the switching device to SINGLE SEQUENTIAL
ACTUATION MECHANISM.
2) Pull the trigger rapidly and firmly.
○ Continuous operation (Push lever firing)
1) Do not press the stapler against the wood with
excessive force.
2) Separate the stapler from the wood as it recoils after
fastening.
16. Take care when stapling thin boards or the corners
of wood.
When stapling thin boards, the staples may pass right
through, as may also be the case when stapling the
corners of wood due to deviation of the staples. In such
cases, always make sure that there is no one (and
nobody's hands or feet; etc.) behind the thin board or
next to the wood you are going to staple.
17. Simultaneous staping on both sides of the same
wall is dangerous.
Under no circumstances should stapling be performed
on both sides of a wall at the same time. This would be
very dangerous since the staples might pass through
the wall and thus cause injuries.
18. Do not use the power tool on scaffoldings, ladders.
The power tool shall not be used for specific application
for example:
–
when changing one driving location to another
involves the use of scaffoldings, stairs, ladders or
ladder alike constructions, e.g. roof laths,
–
closing boxes or crates,
–
fitting transportation safety systems e.g. on vehicles
and wagons
19. Remove all remaining fasteners and battery from
stapler when:
1) doing maintenance and inspection;
2) checking proper operation of push lever and trigger;
3) attaching or removing the nose cap;
4) clearing a jam;
5) it is not in use;
6) leaving work area;
7) moving it to another location; and
8) handing it to another person.
Never attempt to clear a jam or repair the Stapler unless
you have removed battery and all remaining fasteners
from the Stapler.
The Stapler should never be left unattended since
people who are not familiar with the Stapler might
handle it and injure the themselves.
20. Remove battery from stapler when:
1) loading staples;
2) turning the adjuster.
21. Disconnect the battery.
When attaching and detaching the nose cap,
disconnect the battery.
When attaching the accessory nose cap to the tip of the
push lever and when detaching it, make sure to
disconnect the battery beforehand. It is very dangerous
for a staple to be fired by mistake.
22. The operating environment for this device is
between 0°C and 40°C so ensure use within this
temperature range. The device may fail to operate
below 0°C or above 40°C.
23. Always charge the battery at a temperature of 0°C–
40°C.
A temperature of less than 0°C will result in over
charging which is dangerous. The battery cannot be
charged at a temperature higher than 40°C. The most
suitable temperature for charging is that of 20°C–25°C.
24. Do not use the charger continuously.
When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
25. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
26. Never disassemble the rechargeable battery or
charger.
27. Never short-circuit the rechargeable battery.
Short-circuiting the battery will cause a great electric
current and overheat. It results in burn or damage to the
battery.
28. Do not dispose of the battery in fire.
If the battery is burnt, it may explode.
29. Using an exhausted battery will damage the
charger.
30. Bring the battery to the shop from which it was
purchased as soon as the post-charging battery
life becomes too short for practical use.
Do not dispose of the exhausted battery.
31. Do not insert objects into the air ventilation slots
of the charger.
Inserting metal objects or inflammables into the charger
air ventilation slots will result in electrical shock hazard
or a damaged charger.
32. NEVER allow magnets (or similar magnetic
devices) to be adjacent to the stapler, because the
stapler has a magnetic sensor inside.
Doing so will cause a failure or risk of injury by
malfunction.
33. Resting the unit after continuous work.
34. The power tool is equipped with a temperature
protection circuit to protect the motor. Continuous
work may cause the temperature of the unit to rise,
activating the temperature protection circuit and
automatically stopping operation. If this happens,
allow the power tool to cool before resuming use.
35. This product may cease to operate when an
abnormality is detected. In such cases, check the
items listed under "TROUBLESHOOTING" on
page 18.
36. Do not give a strong shock to the switch panel or
break it. It may lead to a trouble.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with
the protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
9
English
Publicidad
