Publicidad
Operating and installation instructions
Primary switch mode power supplies CP-C.1 range
Note: These operating and installation instructions cannot claim to contain all detailed information of all types of this product
range and can even not consider every possible application of the products. All statements serve exclusively to describe the
product and have not to be understood as contractually agreed characteristics. Further information and data is obtainable from
the catalogues and data sheets of this product, from the local ABB sales organisations as well as on the ABB homepage www.abb.
com. Subject to change without prior notice.
Additional information relating to cULus / ANSI-ISA 12.12 approval:
Units with the Class I, Div. 2 marking on the safety label are suitable for use in Class I, Division 2, Groups A, B, C, D or non-hazardous locations only.
The units are Open Type Power Supplies, which need to be mounted in a fire, mechanically and electrically safe enclosure.
WARNING - EXPLOSION HAZARD - Substitution of components my impair suitability for Class I, Division 2.
WARNING - EXPLOSION HAZARD - Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous.
WARNING- Exposure to some chemicals may degrade the sealing properties of materials used in the sealed relays.
Units are for indoor use only.
Units can be used up to an altitude of max 2000 m.
Units are for "overvoltage category II" (mains supply).
Use in controlled environment.
Surrounding air temperature: See characteristic curves of temperature
The normal mounting orientation is DIN-rail vertical (standard mounting orientation: Input (pri) aligned on bottom; Output (sec) on top side)
Information complémentaire relative à la certification cULus / ANSI-ISA 12.12:
Les unités avec le marquage Class I, Div. 2 sur l'étiquette de securité sont adaptées à une utilisation selon la Classe I, Division 2, Groupes A, B, C, D ou
environnements non dangereux seulement.
Les boîtiers des sources d'alimentation sont de type ouvert, qui doivent être montés dans un coffret offrant une protection mécanique, électrique et incendie.
AVERTISSEMENT - RISQUE D'EXPLOSION - La substitution de composants peut nuire à la conformité Classe I, Division 2
AVERTISSEMENT - RISQUE D'EXPLOSION - Ne pas débrancher un composant avant d'avoir coupé l'alimentation ou d'être en présence d'une zone non dangereuse.
AVERTISSEMENT - L'exposition à certains produits chimiques peuvent dégrader les propriétés d'étanchéité des matériaux utilisés par les relais scellés.
Les unités sont pour un usage intérieur.
Les unités peuvent être utilisées jusqu'à une altitude maximale de 2000 m.
Les unités sont pour "la catégorie de surtension II" (alimentation principale).
Utilisation en milieu contrôlé.
Température ambiante: Voir les courbes caractéristiques de température
La position normale de montage est verticale sur profilé DIN (orientation de montage standard: Entrée (pri) au-dessous, sortie (sec) au-dessus)
4.0 x 0.8 mm (0.16 x 0.03") or PH1
8 mm (0.32")
10 mm (0.39")
8 mm (0.32")
10 mm (0.39")
8 mm (0.32")
10 mm (0.39")
o
L, N,
, L+, L-, 13, 14, I>I
R
L+ L- CP-C.1 24/20.0
0.5 Nm (4.4 lb.in)
1.2 Nm (10.5 lb.in)
0.5...4.0 mm² (20...10 AWG)
2.5...16.0 mm² (12...6 AWG)
0.5...2.5 mm² (20...12 AWG)
2.5...10.0 mm² (12...8 AWG)
0.5...2.5 mm² (20...12 AWG)
2.5...10.0 mm² (12...8 AWG)
LEDs + signaling outputs
OUTPUT OK:
Output voltage U
out
> 92 % of U
out
< 90 % of U
out
POWER RESERVE:
Power reserve:
I
I
R
I ΠI
R
Surrounding air temperature:
CP-C.1; CP-C.1-L: -25 °C to +70 °C operational
CP-C.1-C: -40 °C to +70 °C operational
+60 °C to +70 °C derating see table on page 16
For surrounding temperature
use 75 °C - copper wire only
For surrounding temperature > 60 °C up to 70 °C:
use 90 °C - copper wire only
Use only wires with a minimum dielectric strength of
300V (input) and 30V (output).
Relay
LED green
13-14
V
closed
open
Z
Transistor
LED yellow
I>I
R
OFF
ON (closed)
OFF (open)
V
60 °C:
2
Publicidad
