Hallde SB-4 Instrucciones De Uso página 4

USER INSTRUCTIONS
HALLDE SB-4L
(GB)
CAUTION
When transporting the machine,
lower the lid/lid holder (3E/H)
so that the jug (3I) is securely
closed, and carry the machine
by the handle (1A).
Take care not to injure your hands
on the sharp knives (3J) at the
bottom of the jug.
Never put your hands or any
objects into the jug when the
machine is running.
Always expect the contents of the
jug to splash out, and bear in mind
that it may be dangerous to pro-
cess liquids, etc. that are very hot.
Switch off the machine and remove
the power supply plug from the
socket before cleaning the machine
housing (3K).
The machine housing contains
electrical components, and must
therefore not be washed in a
dishwasher or immersed in water.
Don't use a high-pressure spray
gun for cleaning any part of the
machine.
Only an authorized specialists may
repair the machine and open the
machine housing.
UNPACKING
Check that all of the parts have been
delivered, that the machine operates
as intended, and that nothing has been
damaged in transit. The machine supplier
should be notified of any shortcomings
within eight days.
INSTALLATION
Connect the machine to an electric power
supply which is suitable for the machine.
See under "TECHNICAL SPECIFICATION
OF THE SB-4".
Check that the knife unit (3J) stops rotating
within 4 seconds after the lid/lid holder
(3E/H) has been raised.
Fit the jug (3I) and lid (see under
"ASSEMBLING"). Lower the lid/lid holder
so that the lid closes the jug. Start the
machine. Slowly raise the lid/lid holder
and check that the power supply to
the motor is tripped when the opening
between the top edge of the jug and the
bottom edge of the lid is less than 30 mm.
Remove the jug and lid. Lower the lid
holder to its lower snap position. Turn the
speed setting knob (2D) to position "2"
and check that the machine has not started.
If the above checks reveal that the machine
does not perform correctly, summon a
specialist for remedying the fault before
taking the machine into operation.
OIL DOSING BOWL (3G)
The oil dosing bowl is designed for dosing
and slow feed of oil, etc. while the machine
is running, when making mayonnaise, etc.
ASSEMBLING
If necessary, fit the oil dosing bowl (3G) by
pressing it hard into the lids filler opening
(3F) and turning it clockwise as far as it will
go.
Raise the lid holder (3H) to its upper snap
position and fit the lid (3E) into the lid
holder, so that the lid rests in the lid holder.
Place the jug (3I) on the machine so that it
rests firmly on the four supports (3M).
Lower the lid/lid holder as far as it will go.
DISMANTLING
Raise the lid/lid holder (3E/H) to its upper
snap position.
Remove the lid from the lid holder.
Remove the oil dosing bowl from the lid by
turning it anti-clockwise as far as it will go
and then pulling it upwards.
Remove the jug from the machine.
SPEED SETTING KNOB (2D)
In the "0" position, the machine is switched
off.
In position "1", the machine will run at
the lowest speed. It will run at increasing
speeds as the setting is increased, and will
run at maximum speed in setting "6".
To restart the machine after the lid/lid
holder (3E/H) has been swung up and the
safety switch has been actuated, first turn
the speed setting knob to the "0" position
and then to setting "1" or higher.
THE SPRINTER PULSE FUNCTION
"SPF" (2C)
SPF is used for short bursts at the highest
speed.
As soon as the SPF button (2C) is
depressed, the speed will immediately
increase from the speed set on the speed
setting knob to the highest possible speed.
SPF cannot be activated when the speed
setting knob (2D) is in the "0" position.
GENERAL HINTS FOR FAST
PROCESSING AND BEST RESULTS
To avoid dripping from the lid onto ther
rear of the machine, open the lid/lid holder
(3E/H) only to the upper snap position,
and not all the way to the stop position.
Use the SB-4 only for mixing, whipping,
stirring, chopping and mashing mixtures
that are rich in liquids, such as sauces,
soups, thickening, pastry mixtures,
dressings, mayonnaise, desserts, fruit
drinks, cocktails, milkshakes, etc.
Use a sufficient amount of liquid to ensure
that the mixture is fluid and free-running at
all times.
Start by pouring the liquid into the jug and
then add the solid ingredients (including
ice cubes).
Never use bigger ice cubes than those
normally produced by ice machines.
Start by cutting up the solid ingredients
into pieces of roughly equal sizes but not
exceeding a size that the machine can
easily process.
Add the solid ingredients in batches
instead of adding them all together.
Never fill the jug with so much product that
the machine is not easily able to process it.
Never fill the jug more than up to the top
graduation markings, and bare in mind
that the product volume normally increases
during processing.
Select a speed that produces a column of
air in the centre of the jug.
Use the filler opening (3F) in the lid for
feeding liquids, etc. into the jug while the
machine is running.
When making mayonnaise, add the oil last
and add it slowly, using the oil dosing bowl
(3G).
To avoid splashing, hold your hand over
the filler opening (3F) of the lid, or fit the oil
dosing bowl (3G).