Energy Supply Of The On-Board Computer - Bosch PowerPack 400 BBS261 Manual Del Operador

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

EN-54
English – 6​
Selecting system settings
Fit the on-board computer in the holder and proceed
as follows with the bicycle stationary:
Go to the status page (use the < button (10) on the
control unit to get to the first display) and call up the
<Settings> with the select button.
You can use the – (11) and + (12) buttons to select
the setting you want. You can open the settings, as
well as any additional sub-menus, using the select
button (9). You can use the < button (10) to go back
to the previous menu from any settings menu.
The following settings can be changed in the <Sys
settings>:
– <Dis brgh (Display brightness) [current value]>
– <Time [HH:MM]>
– <Date [DD.Mon.YYYY]>
– <Time zone [Current value]>
– <24h form (24h time format)>
– <Brgh backg. (Bright background)>
– <Imp. units (Imperial units)>
– <Language [Current language]>
– <Reset [name of BUI]>
Setting up the eBike system
Requirements
The eBike system can only be activated when the fol-
lowing requirements are met:
– A sufficiently charged eBike battery is inserted (see
battery operating instructions).
– The on-board computer is properly inserted in the
holder
Switching the eBike system on/off
The following options are available for switching on
the eBike system:
– Put the on-board computer in the holder (5).
– When the on-board computer and the eBike battery
are inserted, briefly press the on/off button (4) of
the on-board computer.
– With the on-board computer inserted, push the on/
off button on the eBike battery (bicycle manufac-
turer-specific solutions are possible where there is
1 270 U20 XBK | (21.06.2018)
no access to the battery on/off button; see the bat-
tery operating instructions).
The drive is activated as soon as you start pedaling
(except for in the push assistance function or with the
assistance level OFF). The motor output depends on
which assistance level is set on the on-board com-
puter.
As soon as you stop pedaling when in normal opera-
tion, or as soon as you have reached a speed of
20/28mph, the eBike drive unit switches off the as-
sistance. The drive is automatically re-activated as
soon you start pedalling again and the speed is below
20/28 mph.
The following options are available for switching off
the eBike system:
– Press the on/off button (4) of the on-board com-
puter for at least one second.
– Switch off the eBike battery using its on/off button
(bicycle manufacturer-specific solutions are possi-
ble where there is no access to the battery on/off
button; see the bicycle manufacturer operating in-
structions).
– Remove the on-board computer from its holder.
If no power is drawn from the eBike drive for about
10 minutes (e.g. because the eBike is not moving)
and no button is pressed on the on-board computer
or the operating unit of the eBike, the eBike system,
and therefore also the battery, will switch off auto-
matically to save energy.

Energy supply of the on-board computer

If the on-board computer is in the holder (5), a suffi-
ciently charged eBike battery is inserted in the eBike
and the eBike system is switched on, the on-board
computer battery will be powered by the eBike bat-
tery.
If the on-board computer is removed from the holder
(5), the device will be powered by the on-board com-
puter battery. If the on-board computer battery is
running low on power, a warning message will be
shown on the display.
Bosch eBike Systems

Publicidad

Tabla de contenido
loading

Tabla de contenido