Cameo PIXBAR 600 PRO IP65 Manual De Usuario página 16

OPERATION / BEDIENUNG / UTILISATION / OPERACIÓN / OBSŁUGA / UTILIZZO
EN
NOTE: When the spotlight is properly connected to the mains, the following information appears successively on the display during the startup
process: "Update Wait ..." (only for service purposes), "WELCOME TO cameo" and the software version "SOFTWARE V1.xx". After this operation, the
spotlight is ready for use and changes to the mode that was previously selected.
INTERNAL PROGRAMS
Press the MODE button repeatedly until one of the 15 internal programs appears on the display: Pressing the ENTER button makes the cursor appear
in the top line of the display. Now the desired program 1 - 15 can be selected using the UP and DOWN buttons. Confirm the input with ENTER.
1.MANUAL - Static Colours This program offers the ability to separately adjust the overall brightness and the intensity for each of the 6 LED colours
(R, G, B, W, A and UV) and to generate an unlimited number of different colours (colour mixing).
02.DREAM - Various colours that blend into each other. The brightness and speed of the effect is separately adjustable and a stroboscope effect can
also be activated.
03.METEOR - Pixel Control Program. The individual LEDs are activated one after the other in specific sequences with varying colours. The brightness
and speed of the effect is separately adjustable and a stroboscope effect can also be activated.
04.FADE - Pixel Control Program. The individual LEDs are activated one after the other in a specific sequence with varying colours that blend into
each other. The brightness and speed of the effect is separately adjustable and a stroboscope effect can also be activated.
05.CHANG (Change) - Various alternating colours. The brightness and speed of the effect is separately adjustable and a stroboscope effect can also
be activated.
06.-15. FLOW1-10 - Pixel Control Programs. All FLOW programs consist of various programmed colour change effects. The brightness and speed of
the effect is separately adjustable and a stroboscope effect can also be activated.
To change the brightness and colour in program 1. MANUAL, press the ENTER button repeatedly to select the menu item "Dimmer" to adjust the
overall brightness (Dimmer00 - Dimmer99) and the colour for which you would like to change the intensity for individual colour mixing (note the
cursor on the display, Rxx = red, Gxx = green, Bxx = blue, Wxx = white, Axx = amber, Uxx = UV/black light). Now you can set the intensity of the
selected light from 00 to 99 using the UP and DOWN buttons (example: R00 = red at 0%, i.e. out. R99 = red at 100%, i.e. maximum brightness).
Adjust the flash frequency of the strobe effect by pressing ENTER repeatedly until the cursor shows "Fxx". Now you can activate the strobe effect
using the UP and DOWN buttons and set the flash frequency from 00 to 99 (F00 = strobe effect deactivated, F01 = approx. 1 Hz, F99 = approx. 20
Hz). Confirm with ENTER.
Dimmer Overall brightness Dimmer 00-99
Red Intensity R00 - R99
Green Intensity G00 - G99
Blue Intensity B00 - B99
white Intensity W00 - W99
Amber Intensity A00 - A99
UV / BLACK LIGHT Intensity U00 - U99
Stroboscope Speed F00 - F99
Programs 02 to 15 can be adjusted separately in terms of brightness, speed and stroboscope frequency. Press ENTER repeatedly until the cursor
appears in the top line of the display and then use the UP and DOWN buttons to select the desired program 02 – 15. Press ENTER again to confirm
the operation and to place the cursor in the bottom line on the "Dimmer" field. Using the UP and DOWN buttons, adjust the brightness. Press ENTER
again to adjust the running speed "SPxx" using the UP and DOWN buttons (SP00 = slowest, SP99 = fastest speed).
Pressing the ENTER button again confirms the input and moves the cursor to the "Fxx" field. Using the UP and DOWN buttons, you can activate the
strobe effect and adjust the strobe frequency from 00 to 99 (F00 = strobe effect deactivated, F01 = approx. 1 Hz, F99 = approx. 20 Hz). Confirm with
ENTER.
For example:
AUTO RUN
In the AUTO RUN mode, various programs run in succession. Press the MODE button repeatedly until "AUTO RUN" appears on the display. Press
ENTER to move the cursor to the "Dimmer" field in the bottom line. Using the UP and DOWN buttons, adjust the brightness. Press ENTER again to
confirm the change and move the cursor to the field "FQN:xx" in the bottom line. Using the UP and DOWN buttons, the number of repetitions of each
program can be adjusted (FQN:01 = single repetition, FQN:99 = 99 repetitions of the program). Press ENTER to confirm the input.
DIMMER CURVE (DIMCURVE)
Press the MODE button repeatedly until "DIMCURVE" appears on the display. Press ENTER and using the UP and DOWN buttons, select one of the 4
available dimmer curves. Confirm with ENTER.
16