Select Trigger Setup - Yamaha DTXPRESS III Manual De Instrucciones

Setting Up

Select Trigger Setup

This setting lets you select the Trigger Setup that is best matched
to the particular drum set you are using.
If you switch the type of drum set you are using with the
DTXPRESS III, make sure you use the procedure below to select
an appropriate setup.
1. Press the [TRIG] button to display the Trig-
ger Setup display.
2. Use the [VALUE–]/[VALUE+] buttons to se-
lect the trigger setup that best matches the
drum set you are using.
Trigger Setup List
1 STD Med
(for Standard Drum Set)
Normal setting
2 STD Dyna
(for Standard Drum Set)
Wide dynamic range. This setting is well suited for repro-
ducing expressive subtleties over a wide dynamic range.
Excessive vibration however, may result in crosstalk (sound
being produced by other pads).
3 STD Easy
(for Standard Drum Set)
Controlled dynamic range delivers stable trigger detection.
This setting is well suited for producing a smoother, more
uniformed sound with less expression.
4 SP Med
(for Special Drum Set)
Normal setting
5 SP Dyna
(for Special Drum Set)
Wide dynamic range. This setting is well suited for repro-
ducing expressive subtleties over a wide dynamic range.
Excessive vibration however, may result in crosstalk (sound
being produced by other pads).
6 SP Easy
(for Special Drum Set)
Controlled dynamic range delivers stable trigger detection.
This setting is well suited for producing a smoother, more
uniformed sound with less expression.
7 DT10/20
(for DT10/20)
Use DT10/20 drum trigger systems applied to acoustic
drums.
8 UserTrig 11 UserTrig
—
Lets the user create custom trigger setups. (→ Settings are
made using the [Trigger Setup Edit Mode] (Reference Guide
: P. 11))
12
TRIG __________
1 STD Med
TRIG __________
1 STD Med
Trigger Setup
(for User)
Some Advice on Connections
• Trigger Input Jacks from 1 KICK to 8 HI HAT are stereo
input type jacks.
Pads equipped with trigger switches like the TP65S,
PCY65S, PCY130S, etc. can be connected to these jacks.
• 3-zone pads like the TP65S, PCY150S, etc. can be con-
nected to Trigger Input Jacks 2 SNARE, 6 RIDE, and 7
CRASH1.
• The DTXPRESS III's input jack parameters are preset with
settings suitable for pads that correspond to the input's la-
1 bel (KICK, SNARE, etc.). If any other type of pad is go-
ing to be connected to an input jack, that jack's parameters
(sensitivity, etc.) should be changed to settings that suit
the pad.
• Sensitivity is set in the Trigger Setup Edit mode's [1-1.
Pad Type] (Reference Guide : P. 12).
• The input sensitivity switches (INPUT ATTENUATION)
are sensitivity switches that correspond to Trigger Input
1
Jacks 1 KICK-6 RIDE.
The switch's L position corresponds to a low sensitivity
for pads like TP, KP, PCY, BP, etc. The H position corre-
sponds to a high sensitivity proper for use with the DT20
Drum Trigger, etc.
• The HH series Hi-Hat Controller can be used as a kick
pedal (assign settings in section [1-1. Pad Type] (Refer-
ence Guide : P. 12)).
• In addition to the 1 KICK jack, the 9 CRASH2/10 jack
can be used to connect a second bass drum pedal to create
a double-bass drum set.
• The 9 CRASH2/10 jacks correspond to a 2-trigger input
that uses a stereo jack for L (9) and R (10).
You can use an conversion cable plug (stereo plug m mon-
aural plug x2) to input two separate trigger signals.
When a stereo cable is used to connect the KP65 Kick
Pad, you can use the KP65's Input Jack as the input for the
DTXPRESS III's Trigger Input Jack 10 (assign settings in
section [2-3. Input Exchange] (Reference Guide : P. 15).