Additional Specific Safety Rules - Delta UniSAW 36-L336 Manual De Instrucciones

ADDITIONAL SPECIFIC SAFETY RULES

1. Always use safety glasses. Everyday eyeglasses are
not safety glasses. Also use face or dust mask if cutting
operation is dusty. All users and bystanders must always
wear certified safety equipment:
• ANSI Z87 .1 Eye protection (CAN/CSA Z94.3)
• ANSI S12.6 (S3.19) Hearing protection
• NIOSH/OSHA/MSHA respiratory protection.
Do not expose to rain or use in damp locations.
2.
3. Avoid awkward positions where a sudden slip could
cause a hand to move into a saw blade.
4. Never reach in back of, or around, the cutting tool with
either hand to hold down the workpiece.
5. Keep arms, hands and fingers away from the blade to
prevent serious injury.
6. Use a push stick that is appropriate to the application
to push workpieces through the saw. A push stick is a
wooden or plastic stick, usually homemade, that should be
used whenever the size or shape of the workpiece would
cause you to place your hands within 6" (152 mm) of the
blade.
7. Use hold-downs, jigs, fixtures or feather boards to help
guide and control the workpiece. Accessories for use
with your tool are available at extra cost from your local
dealer or authorized service center. Instructions for making
a push stick, a narrow rip auxiliary fence, a push block and
feather boards are included in this manual.
8. Do not perform ripping, crosscutting or any other
operation freehand.
9. Stability. Make sure the table saw is firmly mounted to a
secure surface before use and does not move.
10. Never cut metals, cement board or masonry.
Certain man-made materials have special instructions
for cutting on table saws. Follow the manufacturer's
recommendations at all times. Damage to the saw and
personal injury may result.
11. The proper throat plate must be in place at all times
to reduce the risk of a thrown workpiece and possible
injury.
12. Use the correct saw blade for the intended operation.
The blade must rotate toward the front of the saw. Always
tighten the blade arbor nut securely. Before use, inspect
the blade for cracks or missing teeth. Do not use a
damaged or dull blade.
13. Never attempt to free a stalled saw blade without first
turning the machine off and disconnecting the saw
from the power source. If a workpiece or cut-off piece
becomes trapped inside the blade guard assembly, turn
saw off and wait for blade to stop before lifting the blade
guard assembly and removing the piece.
Failure to follow these rules may result in serious personal injury.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
14. Never start the machine with the workpiece against
the blade to reduce the risk of a thrown workpiece and
personal injury.
15. Never have any part of your body in line with the path
of the saw blade. Personal injury may occur.
16. Never perform layout, assembly or set-up work on the
table/work area when the machine is running. A sudden
slip could cause a hand to move into the blade. Severe
injury can result.
17. Clean the table/work area before leaving the machine.
Lock out the switch and disconnect from the power source
to prevent unauthorized use.
18. Do not leave a long board (or other workpiece)
unsupported so the spring of the board causes
it to shift on the table resulting in loss of control
and possible injury. Provide proper support for the
workpiece, based on its size and the type of operation to
be performed. Hold the work firmly against the fence and
down against the table surface.
19. If your saw makes an unfamiliar noise or if it vibrates
excessively, cease operating immediately, turn unit off
and disconnect from power source until the problem
has been located and corrected. Contact a DELTA
Power Equipment Corporation factory service center, a
DELTA Power Equipment Corporation authorized service
®
center or other qualified service personnel if the problem
can not be found.
20. Use recommended accessories. The use of improper
accessories may cause risk of personal injury.
21. Do not operate this machine until it is completely
assembled and installed according to the instructions.
A machine incorrectly assembled can cause serious injury.
22. Obtain advice from your supervisor, instructor, or
another qualified person if you are not thoroughly
familiar with the operation of this machine. Knowledge
is safety.
23. Additional information regarding the safe and proper
operation of power tools (i.e., a safety video) is available
from the Power Tool Institute, 1300 Sumner Avenue,
Cleveland, OH 44115-2851 (www.powertoolinstitute.com).
Information is also available from the National Safety
Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201.
Please refer to the U.S. Department of Labor OSHA
1910.213 Regulations.
4
®