Making And Receiving Calls; Speed Dialing - Sony Spread Spectrum 900 Serie Manual De Instrucciones

Handset spare battery usage
As only one battery pack is supplied with this unit, it is necessary to purchase an additional
battery pack (optional) for use as a handset spare battery pack.
1
2
BP-T31
SPARE
3
BATTERY lamp

Making and receiving calls

Making calls
BATT
4
LOW lamp
VOL
2
switch
(FLASH)
(REDIAL)
(*TONE)
Receiving calls
1
When you hear the phone ring;
• Press (TALK) (or any key except (OFF)).
or
• Pick up the handset from the base unit when the handset is placed on the base unit.
TALK button
The lights up.
2 When you're done talking, press (OFF) or replace the handset on the base unit. The
button
goes off.
EZfit
The "EZfit" adjusts to fit any shape ear,
thereby ensure clear voice reception.
Additional tasks
To Do this
Adjust the handset Set the VOL switch to H (high), M (middle) or L (low).
volume
Press (*TONE) after you're connected.
Switch to tone
dialing temporarily
The line will remain in tone dialing until disconnected.
Press (FLASH).
Switch to another
call ("call waiting
Press the button again to get back to the first caller.
service"*)
* Contact your telephone company to subscribe to this service.
1
Open the battery compartment lid of the
base unit.
2
Insert the battery pack (optional) into the
battery compartment.
3
Close the battery compartment lid.
The SPARE BATTERY lamp lights up.
Charge the battery pack for more than 24
hours so that the battery is fully charged.
The SPARE BATTERY lamp remains lit
even after charging is completed.
1
Pick up the handset from the base unit.
2
Press (TALK), and wait until the TALK
button lights up.
The dialing keys light up.
You then hear a dial tone. If you hear
five short error beeps, move closer to the
base unit.
3
Dial the phone number.
4
When you're done talking, press (OFF)
or replace the handset on the base unit.
The TALK button goes off.
Notes
• When you increase the sound volume, in some cases the back ground noise may be increased as well.
You should adjust the volume accordingly.
• If the handset beeps every second during conversation, move closer to the base unit; otherwise, the call
will be disconnected after one minute.
Tip
You can save battery power by setting the RING switch on the
bottom to OFF.
The handset won't ring, but you can still make calls. You can also
receive calls if another telephone connected to the same line rings
to inform you of incoming calls. However, you cannot page the
handset from the base unit.
If the battery becomes weak during a call
The handset will beep twice per second with the BATT LOW lamp flashing at the same time.
Finish your call and charge the battery pack.
For optimum performance, charge the battery for a full 12 hours.
Note that during the initial charge time (approx. 10 minutes) the BATT LOW lamp lights up
and the phone cannot be used.
After the BATT LOW lamp goes off, you may be able to use the phone, but the battery
duration will be very short; thus it is recommended that you fully charge the battery before
next use.
Redialing
1 Press (TALK), and wait until the TALK button lights up.
2 Press (REDIAL) to redial the number last dialed.
Note
If the number exceeds 32 digits or if it is erased, five short error beeps will alert you that the number cannot
be dialed.
To erase the last phone number dialed
Press (REDIAL) twice.
The number will be erased from the memory, and you'll hear a long confirmation beep.

Speed dialing

You can dial with a touch of a few keys by storing a phone number on a dialing key.
Storing phone numbers
(TALK)
2
Note
Do not allow more than 20 seconds to elapse between each step of the procedure.
Tips
• If you enter a wrong number, press (PGM), then start from the beginning.
• Use the supplied directory to write down what you stored on the speed dialing numbers.
TALK
To store a number to be dialed via Private Branch
Exchange (PBX)
Before entering a phone number in step 4, do as follows:
1
Enter the outside line access digit (e.g., 9).
2 Press (PAUSE).
To change a stored number
Store a new number, as described previously.
Making calls with speed dialing
1 Press (TALK) and wait until the TALK button lights up.
2 Press (SPEED DIAL).
3 Enter the desired speed dialing number ((0) to (9)).
The phone number stored in the speed dialing number will be dialed.
RING
switch
1
Press (PGM).
The TALK button flashes.
2
Press (SPEED DIAL).
The dialing keys light up.
3
Press one of the dialing keys ((0) to (9))
to store a phone number on.
You hear a confirmation beep.
1, 5
4
Enter the phone number you want to store.
(PAUSE)
You can enter up to 20 digits, including a
tone and a pause, each of which is counted
as one digit.
5
Press (PGM).
You hear a long confirmation beep, and the
number is stored. The TALK button goes
off.